Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the multi-media module receiver assembly and combination meter assembly.

DTC No. DTC Detection Condition Trouble Area
B1324 After the multi-media module receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the engine switch is on (ACC), 1 or more times, the multi-media module receiver assembly does not receive the signal for 30 seconds or more.
·

Combination meter assembly

·

Multi-media module receiver assembly

·

Harness or connector



WIRING DIAGRAM

E268494E80
1.656,0.438 2.271,0.635 0.615,0.198 10 false MSCH 1.667,1.083 2.281,1.281 0.615,0.198 10 false MSCL 5.083,0.427 5.698,0.625 0.615,0.198 10 false CNH2 5.094,1.083 5.708,1.281 0.615,0.198 10 false CNL2 2.156,0.281 2.771,0.479 0.615,0.198 10 false 37 2.156,0.927 2.771,1.125 0.615,0.198 10 false 38 4.823,0.292 5.438,0.49 0.615,0.198 10 false 20 4.844,0.927 5.458,1.125 0.615,0.198 10 false 21 0.75,1.552 1.365,1.75 0.615,0.198 10 false E119 0.771,1.76 2.74,1.99 1.969,0.229 10 false Combination Meter Assembly 4.771,1.542 5.385,1.74 0.615,0.198 10 false F77 4.771,1.75 6.583,2.063 1.813,0.313 10 false Multi-media Module Receiver Assembly 0.938,2.24 3.302,2.469 2.365,0.229 10 false : Local Bus Communication Line

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-20 (CNH2) - E119-37 (MSCH) Always Below 1 Ω
F77-21 (CNL2) - E119-38 (MSCL) Always Below 1 Ω
F77-20 (CNH2) - Body ground Always 10 kΩ or higher
F77-21 (CNL2) - Body ground Always 10 kΩ or higher
F77-20 (CNH2) - F77-21 (CNL2) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F77-20 (CNH2) - Body ground Always Below 1 V
F77-21 (CNL2) - Body ground Always Below 1 V




OK

2.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY
a.

Remove the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.
E317642E02
0.583,1.792 0.729,1.792 0.729,1.792 0.906,1.313 true 1.292,1.792 1.167,1.792 1.167,1.792 1.052,1.313 true 0.219,1.719 0.833,1.917 0.615,0.198 10 false LCL+ 1.344,1.698 1.958,1.896 0.615,0.198 10 false LCL-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
37 (MSCH) - 38 (MSCL) Always 108 to 132 Ω




OK

3.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.

Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.
E329640E01
1.997,0.215 2.416,0.409 0.419,0.194 10 CNH2 1.908,1.655 2.327,1.849 0.419,0.194 10 CNL2 2.406,1.748 2.529,1.748 2.529,1.748 2.755,1.075 false 2.512,0.313 2.635,0.313 2.635,0.313 2.861,0.986 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
20 (CNH2) - 21 (CNL2) Always 108 to 132 Ω




OK

4.REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

4.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

5.CHECK METER / GAUGE SYSTEM

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

5.CHECK METER / GAUGE SYSTEM
a.

Turn the engine switch on (IG) and wait 30 seconds.


b.

Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

OK:

Audio system returns to normal.




OK

END

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY