Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the multi-media module receiver assembly, multi-display assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E339527E04
6.146,1.677 7.01,2.052 0.865,0.375 10 false Multi-display Assembly 6.167,1.229 6.542,1.427 0.375,0.198 10 false ILL- 6.198,3.677 6.573,3.875 0.375,0.198 10 false ILL- 6.177,5.083 6.552,5.281 0.375,0.198 10 false ILL+ 6.188,0.656 6.458,0.854 0.271,0.198 10 false ILL 5.76,1.229 6.146,1.427 0.385,0.198 10 false F97 5.854,1.021 5.99,1.219 0.135,0.198 10 false 7 5.854,0.458 5.99,0.656 0.135,0.198 10 false 2 5.771,0.656 6.156,0.854 0.385,0.198 10 false F79 2.625,0.823 3.74,1.021 1.115,0.198 10 false PANEL NO.2 0.875,0.677 1.99,0.875 1.115,0.198 10 false from TAIL Relay 5.823,6.104 7.135,6.479 1.313,0.375 10 false Multi-media Module Receiver Assembly 5.823,5.917 6.208,6.115 0.385,0.198 10 false F77 5.875,3.573 6.125,3.771 0.25,0.198 10 false 13 5.896,5 6.146,5.198 0.25,0.198 10 false 14 0.969,6.115 1.771,6.313 0.802,0.198 10 false for RH Side 0.958,3.708 1.76,3.906 0.802,0.198 10 false for LH Side 3.5,4.969 3.958,5.167 0.458,0.198 10 false IL+2 3.49,2.906 3.948,3.104 0.458,0.198 10 false EAU 2.948,5.938 5.01,6.167 2.063,0.229 10 false Spiral Cable Sub-assembly 4.094,5.083 4.542,5.281 0.448,0.198 10 false E122 2.906,2.792 3.125,2.99 0.219,0.198 10 false 8 2.927,4.885 3.146,5.083 0.219,0.198 10 false 5 4.198,4.885 4.417,5.083 0.219,0.198 10 false 13 4.094,3.031 4.458,3.229 0.365,0.198 10 false E122 4.229,2.792 4.406,2.99 0.177,0.198 10 false 3 2.833,3.01 3.156,3.208 0.323,0.198 10 false z73 2.823,5.094 3.146,5.292 0.323,0.198 10 false z73 0.5,6.615 2.563,6.885 2.063,0.271 10 false Steering Pad Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuse for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the multi-media module receiver assembly, multi-display assembly, steering pad switch assembly or others (hazard switch etc.) comes on when the light control switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except multi-display assembly. B
Illumination comes on for all components except multi-media module receiver assembly. C
No illumination comes on (multi-media module receiver assembly, multi-display assembly, steering pad switch, hazard switch, heater control switch, etc.). D



A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)

B

4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)

C

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

D

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)
a.
U166423E01
1.496,0.255 1.852,0.392 0.356,0.137 10 E122 2.785,1.813 3.141,1.949 0.356,0.137 10 IL+2 0.358,0.704 0.713,0.841 0.356,0.137 10 EAU 0.222,0.089 0.578,0.226 0.356,0.137 10 *a 1.476,1.151 0.862,0.788 0.862,0.788 0.752,0.788 false 2.038,1.54 2.652,1.903 2.652,1.903 2.762,1.903 false

Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E122-3 (EAU) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E122-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166631E01
1.549,1.762 1.879,1.919 0.330,0.157 10 F97 1.549,0.18 1.879,0.337 0.330,0.157 10 F79 0.446,0.526 0.789,0.682 0.344,0.156 10 ILL 1.192,0.919 0.813,0.612 0.813,0.612 0.729,0.612 false 0.098,0.076 0.292,0.232 0.194,0.156 10 *a 0.554,3.006 0.898,3.162 0.344,0.156 10 ILL- 1.35,2.734 1.005,3.097 1.005,3.097 0.922,3.097 false

Disconnect the multi-display assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F97-7 (ILL-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F79-2 (ILL) - Body ground Light control switch in the tail or head position 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-display Assembly)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166457E02
2.104,1.198 2.292,1.938 2.292,1.938 2.188,1.938 false 2.229,1.177 2.604,0.708 2.604,0.708 2.719,0.708 false 1.771,0.427 2.104,0.615 0.333,0.188 10 false F77 1.854,1.844 2.188,2.031 0.333,0.188 10 false ILL- 2.823,0.615 3.156,0.802 0.333,0.188 10 false ILL+ 0.094,0.063 0.427,0.25 0.333,0.188 10 false *a

Disconnect the multi-media module receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-13 (ILL-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F77-14 (ILL+) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR