Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The multi-media module receiver assembly and stereo component amplifier assembly are connected by the MOST communication line.

When a MOST communication error occurs between the multi-media module receiver assembly and stereo component amplifier assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D3 A device that is listed in the MOST network connected device record of the master unit is missing.
·

Stereo component amplifier assembly power source circuit

·

MOST circuit between multi-media module receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Multi-media module receiver assembly



HINT:

For the MOST network, the multi-media module receiver assembly is the master unit.


WIRING DIAGRAM

E349214E01
0.802,0.469 1.677,0.677 0.875,0.208 10 false from Battery 0.823,0.99 1.698,1.198 0.875,0.208 10 false from Battery 1.99,0.594 2.479,0.802 0.49,0.208 10 false AMP2 1.115,3.792 1.604,4 0.49,0.208 10 false SLDI 2.854,0.26 3.01,0.458 0.156,0.198 10 false 1 2.823,0.813 3,1.01 0.177,0.198 10 false 16 2.844,1.385 3,1.583 0.156,0.198 10 false 3 2.813,1.927 2.99,2.125 0.177,0.198 10 false 18 2.865,2.5 3.021,2.698 0.156,0.198 10 false 5 2.844,3.042 3,3.24 0.156,0.198 10 false 6 2.854,3.594 3.01,3.792 0.156,0.198 10 false 7 4.292,0.271 4.448,0.469 0.156,0.198 10 false 2 4.281,0.823 4.438,1.021 0.156,0.198 10 false 3 4.26,1.375 4.417,1.573 0.156,0.198 10 false 4 4.281,2.5 4.438,2.698 0.156,0.198 10 false 5 4.292,3.063 4.448,3.26 0.156,0.198 10 false 6 4.26,3.615 4.417,3.813 0.156,0.198 10 false 7 2.781,0.469 3.146,0.656 0.365,0.188 10 false F74 2.75,1.021 3.115,1.208 0.365,0.188 10 false F74 2.76,1.573 3.125,1.76 0.365,0.188 10 false F74 2.781,2.135 3.146,2.323 0.365,0.188 10 false F74 2.76,2.677 3.125,2.865 0.365,0.188 10 false F85 2.771,3.24 3.135,3.427 0.365,0.188 10 false F85 2.75,3.792 3.115,3.979 0.365,0.188 10 false F85 4.198,2.688 4.563,2.875 0.365,0.188 10 false F85 4.188,3.25 4.552,3.438 0.365,0.188 10 false F85 4.188,3.802 4.552,3.99 0.365,0.188 10 false F85 4.188,0.458 4.552,0.646 0.365,0.188 10 false F85 4.188,1.021 4.552,1.208 0.365,0.188 10 false F85 4.177,1.573 4.542,1.76 0.365,0.188 10 false F85 1.521,2.573 1.677,2.771 0.156,0.198 10 false 2 1.51,3.135 1.667,3.333 0.156,0.198 10 false 3 1.5,3.719 1.656,3.917 0.156,0.198 10 false 4 1.865,3.917 2.469,4.125 0.604,0.208 10 false Shielded 4.813,3.948 5.417,4.156 0.604,0.208 10 false Shielded 4.833,1.74 5.438,1.948 0.604,0.208 10 false Shielded 0.708,3.104 0.885,3.302 0.177,0.198 10 false *2 1.177,2.698 1.438,2.896 0.26,0.198 10 false MI+ 1.198,3.25 1.521,3.448 0.323,0.198 10 false MI- 2,1.188 2.49,1.396 0.49,0.208 10 false AMP1 3.177,0.458 3.438,0.656 0.26,0.198 10 false +B 3.823,1.01 4.146,1.208 0.323,0.198 10 false MI- 3.729,1.583 4.219,1.792 0.49,0.208 10 false SLDI 3.781,0.458 4.042,0.656 0.26,0.198 10 false MI+ 3.177,1.01 3.521,1.198 0.344,0.188 10 false +B2 3.167,1.573 3.51,1.76 0.344,0.188 10 false GND 3.167,2.125 3.583,2.323 0.417,0.198 10 false GND2 3.156,2.688 3.531,2.885 0.375,0.198 10 false MO+ 3.146,3.219 3.521,3.417 0.375,0.198 10 false MO- 3.156,3.781 3.552,3.99 0.396,0.208 10 false SLDO 3.729,2.688 4.104,2.885 0.375,0.198 10 false MO+ 3.74,3.229 4.115,3.427 0.375,0.198 10 false MO- 3.688,3.781 4.083,3.99 0.396,0.208 10 false SLDO 5.594,0.365 5.75,0.563 0.156,0.198 10 false 5 5.615,0.927 5.771,1.125 0.156,0.198 10 false 6 5.615,1.51 5.771,1.708 0.156,0.198 10 false 7 5.781,0.49 6.156,0.688 0.375,0.198 10 false MO+ 5.792,1.021 6.167,1.219 0.375,0.198 10 false MO- 5.781,1.583 6.177,1.792 0.396,0.208 10 false SLDO 5.792,2.688 6.052,2.885 0.26,0.198 10 false MI+ 5.792,3.26 6.115,3.458 0.323,0.198 10 false MI- 5.792,3.813 6.281,4.021 0.49,0.208 10 false SLDI 5.615,2.604 5.771,2.802 0.156,0.198 10 false 2 5.604,3.146 5.76,3.344 0.156,0.198 10 false 3 5.604,3.729 5.76,3.927 0.156,0.198 10 false 4 6.344,3.063 6.521,3.26 0.177,0.198 10 false *1 5.719,4.25 6.042,4.448 0.323,0.198 10 false F84 0.385,4.375 2.365,4.604 1.979,0.229 10 false Television Display Assembly*2 3.063,4.26 4.365,4.656 1.302,0.396 10 false Stereo Component Amplifier Assembly 5.719,4.406 7.021,4.802 1.302,0.396 10 false Multi-media Module Receiver Assembly 0.396,4.219 0.719,4.417 0.323,0.198 10 false L56 0.635,5.406 2.521,5.635 1.885,0.229 10 false : MOST Communication Line 0.198,5.063 2.667,5.302 2.469,0.24 10 false *2: w/ Rear Seat Entertainment System 0.188,4.76 2.781,4.99 2.594,0.229 10 false *1: w/o Rear Seat Entertainment System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.

·

This DTC may be stored when a MOST communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CLEAR DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

3.CLEAR DTC
4.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166280E02
0.781,1.302 0.625,1.854 false 1.094,1.292 1.375,1.771 false 0.74,1.094 0.375,0.896 false 1.031,1.104 0.646,0.615 false 0.083,0.042 0.25,0.229 0.167,0.188 10 false *a 1.521,0.396 1.802,0.563 0.281,0.167 10 false F74 0.365,0.458 0.719,0.625 0.354,0.167 10 false GND 0.104,0.74 0.344,0.906 0.24,0.167 10 false +B 1.25,1.802 1.677,1.979 0.427,0.177 10 false GND2 0.448,1.885 0.781,2.063 0.333,0.177 10 false +B2

Disconnect the stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-3 (GND) - Body ground Always Below 1 Ω
F74-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F74-1 (+B) - F74-3 (GND) Always 11 to 14 V
F74-16 (+B2) - F74-3 (GND) Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)

Result
Result Proceed to
OK (w/o Rear Seat Entertainment System) A
OK (w/ Rear Seat Entertainment System) B
NG C


A

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-MEDIA MODULE RECEIVER AND TELEVISION DISPLAY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F84 multi-media module receiver assembly connector.


b.

Disconnect the F85 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-2 (MI+) - F85-5 (MO+) Always Below 1 Ω
F84-3 (MI-) - F85-6 (MO-) Always Below 1 Ω
F84-4 (SLDI) - F85-7 (SLDO) Always Below 1 Ω
F84-5 (MO+) - F85-2 (MI+) Always Below 1 Ω
F84-6 (MO-) - F85-3 (MI-) Always Below 1 Ω
F84-7 (SLDO) - F85-4 (SLDI) Always Below 1 Ω
F84-2 (MI+) - Body ground Always 10 kΩ or higher
F84-3 (MI-) - Body ground Always 10 kΩ or higher
F84-4 (SLDI) - Body ground Always 10 kΩ or higher
F84-5 (MO+) - Body ground Always 10 kΩ or higher
F84-6 (MO-) - Body ground Always 10 kΩ or higher
F84-7 (SLDO) - Body ground Always 10 kΩ or higher




OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



NEXT

8.CLEAR DTC
9.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output




OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-MEDIA MODULE RECEIVER AND TELEVISION DISPLAY)
a.

Disconnect the F84 multi-media module receiver assembly connector.


b.

Disconnect the F85 stereo component amplifier assembly connector.


c.

Disconnect the L56 television assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-5 (MO+) - F85-2 (MI+) Always Below 1 Ω
F84-6 (MO-) - F85-3 (MI-) Always Below 1 Ω
F84-7 (SLDO) - F85-4 (SLDI) Always Below 1 Ω
F85-5 (MO+) - L56-2 (MI+) Always Below 1 Ω
F85-6 (MO-) - L56-3 (MI-) Always Below 1 Ω
F85-7 (SLDO) - L56-4 (SLDI) Always Below 1 Ω
F85-2 (MI+) - Body ground Always 10 kΩ or higher
F85-3 (MI-) - Body ground Always 10 kΩ or higher
F85-4 (SLDI) - Body ground Always 10 kΩ or higher
F85-5 (MO+) - Body ground Always 10 kΩ or higher
F85-6 (MO-) - Body ground Always 10 kΩ or higher
F85-7 (SLDO) - Body ground Always 10 kΩ or higher




OK

11.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



NEXT

12.CLEAR DTC
13.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).



OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY