Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The multi-media module receiver assembly and stereo component amplifier assembly are connected by the MOST communication line.

When a MOST communication error occurs between the multi-media module receiver assembly and stereo component amplifier assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D3 A device that is listed in the MOST network connected device record of the master unit is missing.
·

MOST circuit between multi-media module receiver assembly and stereo component amplifier assembly

·

MOST circuit between multi-display controller sub-assembly and stereo component amplifier assembly*

·

Stereo component amplifier assembly

·

Multi-media module receiver assembly

·

Multi-display controller sub-assembly*

·

Harness or connector



*: w/ Rear Seat Entertainment System


HINT:

For the MOST network, the multi-media module receiver assembly is the master unit.


WIRING DIAGRAM

E330587E04
0.99,2.417 3.583,3.635 2.594,1.219 0.563,1.167 1.646,1.375 1.083,0.208 10 false from Battery 0.563,0.802 1.646,1.01 1.083,0.208 10 false from Battery 2.896,3.177 3.156,3.333 0.26,0.156 10 false 7 2.906,2.813 3.167,2.969 0.26,0.156 10 false 6 2.906,2.438 3.167,2.594 0.26,0.156 10 false 5 3.74,3.344 4.302,3.552 0.563,0.208 10 false SLDO 3.813,2.969 4.375,3.177 0.563,0.208 10 false MO- 3.813,2.615 4.375,2.823 0.563,0.208 10 false MO+ 1.146,3.354 1.708,3.563 0.563,0.208 10 false SLDI 1.229,2.979 1.792,3.188 0.563,0.208 10 false MI- 1.219,2.615 1.781,2.823 0.563,0.208 10 false MI+ 3.167,1.906 3.729,2.115 0.563,0.208 10 false GND2 3.167,1.521 3.729,1.729 0.563,0.208 10 false GND 3.167,1.156 3.729,1.365 0.563,0.208 10 false +B2 3.167,0.813 3.729,1.021 0.563,0.208 10 false +B 3.792,1.677 4.354,1.885 0.563,0.208 10 false SLDI 3.896,1.302 4.458,1.51 0.563,0.208 10 false MI- 3.875,0.948 4.438,1.156 0.563,0.208 10 false MI+ 3.156,3.344 3.719,3.552 0.563,0.208 10 false SLDO 3.156,2.979 3.719,3.188 0.563,0.208 10 false MO- 3.156,2.625 3.719,2.833 0.563,0.208 10 false MO+ 5.698,3.333 6.26,3.542 0.563,0.208 10 false SLDI 5.708,2.979 6.271,3.188 0.563,0.208 10 false MI- 5.708,2.625 6.271,2.833 0.563,0.208 10 false MI+ 5.75,1.615 6.313,1.823 0.563,0.208 10 false SLDO 5.75,1.25 6.313,1.458 0.563,0.208 10 false MO- 5.75,0.885 6.313,1.094 0.563,0.208 10 false MO+ 4.292,3.167 4.552,3.323 0.26,0.156 10 false 7 4.292,2.813 4.552,2.969 0.26,0.156 10 false 6 4.292,2.448 4.552,2.604 0.26,0.156 10 false 5 1.542,3.229 1.802,3.385 0.26,0.156 10 false 4 6.229,2.948 6.49,3.104 0.26,0.156 10 false *1 0.802,2.969 1.063,3.125 0.26,0.156 10 false *2 1.542,2.865 1.802,3.021 0.26,0.156 10 false 3 1.542,2.51 1.802,2.667 0.26,0.156 10 false 2 2.854,1.729 3.115,1.885 0.26,0.156 10 false 18 2.896,1.354 3.156,1.51 0.26,0.156 10 false 3 2.854,1 3.115,1.156 0.26,0.156 10 false 16 2.896,0.635 3.156,0.792 0.26,0.156 10 false 1 4.292,1.51 4.552,1.667 0.26,0.156 10 false 4 4.292,1.146 4.552,1.302 0.26,0.156 10 false 3 4.292,0.781 4.552,0.938 0.26,0.156 10 false 2 5.552,3.24 5.813,3.396 0.26,0.156 10 false 4 5.542,2.875 5.802,3.031 0.26,0.156 10 false 3 5.542,2.521 5.802,2.677 0.26,0.156 10 false 2 5.521,1.583 5.781,1.74 0.26,0.156 10 false 7 5.521,1.208 5.781,1.365 0.26,0.156 10 false 6 5.521,0.844 5.781,1 0.26,0.156 10 false 5 0.344,3.99 1.833,4.344 1.49,0.354 10 false Multi-display Controller Sub-assembly*2 0.344,3.823 1.313,3.979 0.969,0.156 10 false L77 5.635,4.01 6.958,4.396 1.323,0.385 10 false Multi-media Module Receiver Assembly 5.646,3.833 6.083,3.99 0.438,0.156 10 false F102 3.083,3.885 4.375,4.24 1.292,0.354 10 false Stereo Component Amplifier Assembly 2.823,1.906 3.26,2.063 0.438,0.156 10 false F74 2.823,1.521 3.26,1.677 0.438,0.156 10 false F74 2.823,1.167 3.26,1.323 0.438,0.156 10 false F74 2.823,0.813 3.26,0.969 0.438,0.156 10 false F74 4.188,0.958 4.625,1.115 0.438,0.156 10 false F103 1.083,5.469 4.042,5.667 2.958,0.198 10 false : MOST Communication Line 0.521,4.875 3.479,5.073 2.958,0.198 10 false *2: w/ Rear Seat Entertainment System 0.51,4.615 3.469,4.813 2.958,0.198 10 false *1: w/o Rear Seat Entertainment System 1.896,0.969 2.604,1.135 0.708,0.167 10 false AMP NO.2 1.906,1.333 2.781,1.5 0.875,0.167 10 false AMP NO.1 0.521,5.146 1.333,5.292 0.813,0.146 10 false *3: Shielded 4.75,3.448 4.948,3.594 0.198,0.146 10 false *3 5.115,3.448 5.313,3.594 0.198,0.146 10 false *3 1.927,3.458 2.125,3.604 0.198,0.146 10 false *3 2.26,3.458 2.458,3.604 0.198,0.146 10 false *3 5.021,1.802 5.219,1.948 0.198,0.146 10 false *3 4.188,1.313 4.625,1.469 0.438,0.156 10 false F103 4.177,1.677 4.615,1.833 0.438,0.156 10 false F103 4.177,2.625 4.615,2.781 0.438,0.156 10 false F103 4.188,2.99 4.625,3.146 0.438,0.156 10 false F103 4.188,3.344 4.625,3.5 0.438,0.156 10 false F103 2.792,2.625 3.229,2.781 0.438,0.156 10 false F103 2.792,2.99 3.229,3.146 0.438,0.156 10 false F103 2.771,3.344 3.208,3.5 0.438,0.156 10 false F103

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.

·

This DTC may be stored when a MOST communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CLEAR DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

3.CLEAR DTC
4.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166556E02
0.625,1.063 0.448,0.583 0.448,0.583 0.354,0.583 false 0.854,1.104 0.833,0.625 0.833,0.625 0.885,0.625 false 0.594,1.292 0.677,1.865 0.677,1.865 0.615,1.865 false 0.875,1.292 1.104,1.865 1.104,1.865 1.167,1.865 false 1.521,0.323 1.875,0.51 0.354,0.188 10 false F74 0.969,0.552 1.573,0.729 0.604,0.177 10 false GND 0.135,0.521 0.74,0.698 0.604,0.177 10 false +B 1.229,1.792 1.833,1.969 0.604,0.177 10 false GND2 0.302,1.802 0.906,1.979 0.604,0.177 10 false +B2 0.094,0.042 0.385,0.26 0.292,0.219 10 false *a

Disconnect the stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-3 (GND) - Body ground Always Below 1 Ω
F74-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F74-1 (+B) - Body ground Always 11 to 14 V
F74-16 (+B2) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)

Result
Result Proceed to
OK (w/o Rear Seat Entertainment System) A
OK (w/ Rear Seat Entertainment System) B
NG C


A

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-MEDIA MODULE RECEIVER ASSEMBLY AND MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F102 multi-media module receiver assembly connector.


b.

Disconnect the F103 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F102-2 (MI+) - F103-5 (MO+) Always Below 1 Ω
F102-3 (MI-) - F103-6 (MO-) Always Below 1 Ω
F102-4 (SLDI) - F103-7 (SLDO) Always Below 1 Ω
F102-5 (MO+) - F103-2 (MI+) Always Below 1 Ω
F102-6 (MO-) - F103-3 (MI-) Always Below 1 Ω
F102-7 (SLDO) - F103-4 (SLDI) Always Below 1 Ω
F102-2 (MI+) - Body ground Always 10 kΩ or higher
F102-3 (MI-) - Body ground Always 10 kΩ or higher
F102-4 (SLDI) - Body ground Always 10 kΩ or higher
F102-5 (MO+) - Body ground Always 10 kΩ or higher
F102-6 (MO-) - Body ground Always 10 kΩ or higher
F102-7 (SLDO) - Body ground Always 10 kΩ or higher




OK

7.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



NEXT

8.CLEAR DTC
9.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-MEDIA MODULE RECEIVER ASSEMBLY AND MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY)
a.

Disconnect the F102 multi-media module receiver assembly connector.


b.

Disconnect the F103 stereo component amplifier assembly connector.


c.

Disconnect the L77 multi-display controller sub-assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F102-5 (MO+) - F103-2 (MI+) Always Below 1 Ω
F102-6 (MO-) - F103-3 (MI-) Always Below 1 Ω
F102-7 (SLDO) - F103-4 (SLDI) Always Below 1 Ω
F103-5 (MO+) - L77-2 (MI+) Always Below 1 Ω
F103-6 (MO-) - L77-3 (MI-) Always Below 1 Ω
F103-7 (SLDO) - L77-4 (SLDI) Always Below 1 Ω
F103-2 (MI+) - Body ground Always 10 kΩ or higher
F103-3 (MI-) - Body ground Always 10 kΩ or higher
F103-4 (SLDI) - Body ground Always 10 kΩ or higher
F103-5 (MO+) - Body ground Always 10 kΩ or higher
F103-6 (MO-) - Body ground Always 10 kΩ or higher
F103-7 (SLDO) - Body ground Always 10 kΩ or higher




OK

11.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



NEXT

12.CLEAR DTC
13.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).



OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY