Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The multi-media module receiver assembly and multi-display controller sub-assembly are connected by the MOST communication line.

When a MOST communication error occurs between the multi-media module receiver assembly and multi-display controller sub-assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D5 A device that is listed in the MOST network connected device record of the master unit is missing.
·

MOST circuit between stereo component amplifier assembly and multi-display controller sub-assembly

·

MOST circuit between multi-display controller sub-assembly and multi-media module receiver assembly

·

Multi-display controller sub-assembly

·

Multi-media module receiver assembly

·

Harness or connector



HINT:

For the MOST network, the multi-media module receiver assembly is the master unit.


WIRING DIAGRAM

E330009E03
1.083,4.365 3.031,4.563 1.948,0.198 10 false : MOST Communication Line 0.479,3.927 1.396,4.125 0.917,0.198 10 false *: Shielded 0.292,0.646 1.375,0.854 1.083,0.208 10 false from Battery 2.906,2.167 3.052,2.323 0.146,0.156 10 false 4 2.906,1.802 3.052,1.958 0.146,0.156 10 false 3 2.906,1.448 3.031,1.604 0.125,0.156 10 false 2 3.74,2.344 4.167,2.552 0.427,0.208 10 false SLDO 3.823,1.969 4.167,2.177 0.344,0.208 10 false MO- 3.813,1.615 4.208,1.823 0.396,0.208 10 false MO+ 1.073,2.354 1.635,2.563 0.563,0.208 10 false SLDO 1.167,1.969 1.729,2.177 0.563,0.208 10 false MO- 1.156,1.594 1.719,1.802 0.563,0.208 10 false MO+ 3.167,1.01 3.729,1.219 0.563,0.208 10 false +B2 3.167,0.656 3.729,0.865 0.563,0.208 10 false +B 3.729,1.01 4.292,1.219 0.563,0.208 10 false GND5 3.802,0.667 4.365,0.875 0.563,0.208 10 false GND 3.167,2.344 3.521,2.552 0.354,0.208 10 false SLDI 3.156,1.979 3.438,2.188 0.281,0.208 10 false MI- 3.156,1.615 3.417,1.823 0.26,0.208 10 false MI+ 5.708,2.333 6.271,2.542 0.563,0.208 10 false SLDI 5.708,1.969 6.271,2.177 0.563,0.208 10 false MI- 5.708,1.604 6.271,1.813 0.563,0.208 10 false MI+ 4.313,2.156 4.458,2.313 0.146,0.156 10 false 7 4.313,1.802 4.458,1.958 0.146,0.156 10 false 6 4.313,1.448 4.469,1.604 0.156,0.156 10 false 5 1.552,2.24 1.677,2.396 0.125,0.156 10 false 7 1.552,1.854 1.813,2.01 0.26,0.156 10 false 6 1.552,1.5 1.813,1.656 0.26,0.156 10 false 5 2.906,0.844 3.115,1 0.208,0.156 10 false 6 2.906,0.479 3.031,0.635 0.125,0.156 10 false 1 4.25,0.844 4.458,1 0.208,0.156 10 false 15 4.25,0.49 4.458,0.646 0.208,0.156 10 false 14 5.531,2.24 5.792,2.396 0.26,0.156 10 false 4 5.531,1.865 5.792,2.021 0.26,0.156 10 false 3 5.531,1.5 5.792,1.656 0.26,0.156 10 false 2 2.927,2.844 4.406,3.25 1.479,0.406 10 false Multi-display Controller Sub-assembly 0.406,2.823 0.719,2.979 0.313,0.156 10 false F103 5.646,2.99 7.021,3.344 1.375,0.354 10 false Multi-media Module Receiver Assembly 5.656,2.823 5.969,2.979 0.313,0.156 10 false F102 0.396,2.99 1.688,3.344 1.292,0.354 10 false Stereo Component Amplifier Assembly 4.229,1.625 4.667,1.781 0.438,0.156 10 false L77 4.229,0.656 4.667,0.813 0.438,0.156 10 false L67 1.646,0.813 2.042,0.979 0.396,0.167 10 false RSE 2.396,2.458 2.521,2.604 0.125,0.146 10 false * 5.156,2.448 5.281,2.594 0.125,0.146 10 false * 4.76,2.448 4.885,2.594 0.125,0.146 10 false * 1.938,2.458 2.063,2.604 0.125,0.146 10 false * 4.219,1.021 4.656,1.177 0.438,0.156 10 false L67 4.219,1.979 4.656,2.135 0.438,0.156 10 false L77 4.208,2.333 4.646,2.49 0.438,0.156 10 false L77 2.823,2.333 3.26,2.49 0.438,0.156 10 false L77 2.823,1.979 3.26,2.135 0.438,0.156 10 false L77 2.823,1.625 3.26,1.781 0.438,0.156 10 false L77 2.823,0.656 3.26,0.813 0.438,0.156 10 false L67 2.823,1.01 3.26,1.167 0.438,0.156 10 false L67

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.

·

This DTC may be stored when a MOST communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CLEAR DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

3.CLEAR DTC
4.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

NG

5.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166535E01
1.627,0.261 1.912,0.425 0.285,0.164 10 L67 0.128,0.096 0.342,0.246 0.214,0.150 10 *a 0.18,0.588 0.410,0.739 0.230,0.151 10 +B 0.23,1.806 0.534,1.957 0.304,0.151 10 +B2 1.451,1.851 1.783,2.002 0.332,0.151 10 GND 2.855,1.746 3.274,1.898 0.420,0.151 10 GND5 0.773,1.127 0.606,0.66 0.606,0.66 0.481,0.66 false 0.789,1.422 0.713,1.893 0.713,1.893 0.602,1.893 false 2.258,1.408 1.998,1.932 1.998,1.932 1.886,1.932 false 2.448,1.418 2.71,1.847 2.71,1.847 2.818,1.847 false

Disconnect the multi-display controller sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L67-14 (GND) - Body ground Always Below 1 Ω
L67-15 (GND5) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L67-1 (+B) - Body ground Always 11 to 14 V
L67-6 (+B2) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-display Controller Sub-assembly)


OK

6.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the L77 multi-display controller sub-assembly connector.


b.

Disconnect the F103 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L77-2 (MI+) - F103-5 (MO+) Always Below 1 Ω
L77-3 (MI-) - F103-6 (MO-) Always Below 1 Ω
L77-4 (SLDI) - F103-7 (SLDO) Always Below 1 Ω
L77-2 (MI+) - Body ground Always 10 kΩ or higher
L77-3 (MI-) - Body ground Always 10 kΩ or higher
L77-4 (SLDI) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
a.

Disconnect the L77 multi-display controller sub-assembly connector.


b.

Disconnect the F102 multi-media module receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L77-5 (MO+) - F102-2 (MI+) Always Below 1 Ω
L77-6 (MO-) - F102-3 (MI-) Always Below 1 Ω
L77-7 (SLDO) - F102-4 (SLDI) Always Below 1 Ω
L77-5 (MO+) - Body ground Always 10 kΩ or higher
L77-6 (MO-) - Body ground Always 10 kΩ or higher
L77-7 (SLDO) - Body ground Always 10 kΩ or higher




OK

8.REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY
a.

Replace the multi-display controller sub-assembly with a new or normally functioning one (See pageAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT ECU>REMOVAL ).



NEXT

9.CLEAR DTC
10.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY