Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D6  Display Disconnected  


DESCRIPTION

The multi-display assembly and multi-media module receiver assembly are connected by an AVC-LAN communication line.

When an AVC-LAN communication error occurs between the multi-media module receiver assembly and multi-display assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D6* A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Multi-display power source circuit

·

AVC-LAN circuit

·

Multi-display assembly

·

Multi-media module receiver assembly



HINT:
·

*: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The multi-media module receiver assembly is the master unit.



WIRING DIAGRAM

E245658E30
0.344,0.844 1.74,1.052 1.396,0.208 10 false from IG1 NO. 1 Relay 0.833,1.26 1.677,1.458 0.844,0.198 10 false from Battery 0.656,1.688 1.802,1.917 1.146,0.229 10 false from ACC Relay 1.938,1.021 2.896,1.198 0.958,0.177 10 false ECU-IG NO.1 2.177,1.406 2.458,1.625 0.281,0.219 10 false TV 2.125,1.823 2.865,2.01 0.74,0.188 10 false ACC 3.146,0.854 3.885,1.042 0.74,0.188 10 false IG 3.146,1.271 3.885,1.458 0.74,0.188 10 false +B2 3.146,1.688 3.885,1.875 0.74,0.188 10 false ACC 3.135,2.115 3.875,2.302 0.74,0.188 10 false GND1 2.896,0.76 3.635,0.948 0.74,0.188 10 false 23 2.896,1.156 3.635,1.344 0.74,0.188 10 false 12 2.917,1.583 3.656,1.771 0.74,0.188 10 false 24 2.917,1.969 3.656,2.156 0.74,0.188 10 false 13 3.75,1.26 4.49,1.448 0.74,0.188 10 false TX+ 3.792,1.677 4.531,1.865 0.74,0.188 10 false TX- 4.094,1.146 4.833,1.333 0.74,0.188 10 false 7 4.094,1.552 4.833,1.74 0.74,0.188 10 false 19 5.51,1.135 5.823,1.333 0.313,0.198 10 false 45 5.521,1.563 6.26,1.75 0.74,0.188 10 false 46 5.75,1.271 6.49,1.458 0.74,0.188 10 false TX3+ 5.76,1.635 6.5,1.823 0.74,0.188 10 false TX3- 5.604,2.167 6.344,2.354 0.74,0.188 10 false F77 5.594,2.344 6.833,2.708 1.24,0.365 10 false Multi-media Module Receiver Assembly 3.01,2.521 3.75,2.708 0.74,0.188 10 false F79 3.01,2.688 4.656,2.885 1.646,0.198 10 false Multi-display Assembly 0.844,3.448 2.885,3.594 2.042,0.146 10 false : AVC-LAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

2.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output




OK

NG

3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166141E02
2.5,1.521 2.688,1.802 false 2.333,1.531 2.042,1.833 false 0.906,1.51 0.573,1.729 false 2.5,1.25 2.688,0.729 false 0.104,0.083 0.271,0.25 0.167,0.167 10 false *a 1.583,0.448 1.865,0.615 0.281,0.167 10 false F79 2.604,0.531 2.875,0.698 0.271,0.167 10 false +B2 2.604,1.802 2.938,2 0.333,0.198 10 false ACC 1.948,1.865 2.135,2.021 0.188,0.156 10 false IG 0.292,1.75 0.74,1.927 0.448,0.177 10 false GND1

Disconnect the multi-display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F79-12 (+B2) - F79-13 (GND1) Always 11 to 14 V
F79-23 (IG) - F79-13 (GND1) Engine switch on (IG) 11 to 14 V
F79-24 (ACC) - F79-13 (GND1) Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-display Assembly)


OK

4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E238990E03
2.75,1.833 2.583,1.833 2.583,1.833 2.365,1.094 true 1.917,1.833 2.083,1.833 2.083,1.833 2.25,1.115 true 1.646,1.76 2.063,1.958 0.417,0.198 10 false TX- 2.781,1.76 3.198,1.958 0.417,0.198 10 false TX+

Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
45 (TX3+) - 46 (TX3-) Always 60 to 80 Ω




OK

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the F79 multi-display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-45 (TX3+) - F79-7 (TX+) Always Below 1 Ω
F77-46 (TX3-) - F79-19 (TX-) Always Below 1 Ω
F77-45 (TX3+) - Body ground Always 10 kΩ or higher
F77-46 (TX3-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).



NEXT

7.CLEAR DTC
8.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output




OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY