Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the multi-media module receiver assembly and combination meter assembly.

DTC Code DTC Detection Condition Trouble Area
B1324 After the multi-media module receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the engine switch is on (ACC), 1 or more times, the multi-media module receiver assembly cannot receive the signal for 30 seconds or more.
·

Combination meter assembly

·

Multi-media module receiver assembly

·

Harness or connector



WIRING DIAGRAM

E268494E81
1.656,0.438 2.271,0.635 0.615,0.198 10 false MSCH 1.667,1.083 2.281,1.281 0.615,0.198 10 false MSCL 5.083,0.427 5.698,0.625 0.615,0.198 10 false CNH2 5.094,1.083 5.708,1.281 0.615,0.198 10 false CNL2 2.156,0.281 2.771,0.479 0.615,0.198 10 false 37 2.156,0.927 2.771,1.125 0.615,0.198 10 false 38 4.823,0.292 5.24,0.5 0.417,0.208 10 false 20 4.833,0.938 5.063,1.167 0.229,0.229 10 false 21 0.75,1.552 1.365,1.75 0.615,0.198 10 false E119 0.75,1.76 2.719,1.99 1.969,0.229 10 false Combination Meter Assembly 4.771,1.583 5.385,1.781 0.615,0.198 10 false F77 4.781,1.74 6.5,2.125 1.719,0.385 10 false Radio and Display Receiver Assembly 0.906,2.24 3.271,2.469 2.365,0.229 10 false : Local Bus Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-20 (CNH2) - E119-37 (MSCH) Always Below 1 Ω
F77-21 (CNL2) - E119-38 (MSCL) Always Below 1 Ω
F77-20 (CNH2) - Body ground Always 10 kΩ or higher
F77-21 (CNL2) - Body ground Always 10 kΩ or higher
F77-20 (CNH2) - F77-21 (CNL2) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F77-20 (CNH2) - Body ground Always Below 1 V
F77-21 (CNL2) - Body ground Always Below 1 V




OK

2.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY
a.
E317642E03
1.595,1.662 2.139,1.865 0.544,0.204 10 MSCH 0.127,1.631 0.670,1.835 0.544,0.204 10 MSCL 1.026,1.258 1.381,1.736 1.381,1.736 1.524,1.736 false 0.893,1.253 0.699,1.719 0.699,1.719 0.622,1.719 false

Remove the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
37 (MSCH) - 38 (MSCL) Always 108 to 132 Ω




OK

3.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E330007E01
2.774,1.777 3.244,1.929 0.470,0.152 10 CNH2 1.41,1.736 1.880,1.888 0.470,0.152 10 CNL2 2.547,1.202 2.638,1.854 2.638,1.854 2.737,1.854 false 2.467,1.202 2.037,1.832 2.037,1.832 1.911,1.832 false

Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
20 (CNH2) - 21 (CNL2) Always 108 to 132 Ω




OK

4.REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

4.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

5.CLEAR DTC
6.CHECK DTC
a.

Recheck for DTCs and check if the same DTCs are output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY