Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255505 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Image from Camera for Rear View Monitor is Abnormal  


DESCRIPTION

This is the display signal circuit of the rear television camera assembly.

WIRING DIAGRAM

E240589E11
1.781,0.354 2.198,0.563 0.417,0.208 10 false GVIF 5.021,0.333 5.438,0.542 0.417,0.208 10 false GVIF 1.24,0.656 1.656,0.865 0.417,0.208 10 false F83 1.219,0.813 2.865,1.073 1.646,0.26 10 false Multi-display Assembly 2.24,0.208 2.427,0.396 0.188,0.188 10 false 1 4.729,0.135 4.917,0.323 0.188,0.188 10 false 1 2.219,1.99 2.406,2.177 0.188,0.188 10 false 1 2.229,1.219 2.417,1.406 0.188,0.188 10 false 4 2.229,1.615 2.417,1.802 0.188,0.188 10 false 2 2.24,2.396 2.427,2.583 0.188,0.188 10 false 3 4.708,1.115 4.896,1.302 0.188,0.188 10 false 39 4.698,1.521 4.885,1.708 0.188,0.188 10 false 18 4.688,1.917 4.875,2.104 0.188,0.188 10 false 19 4.698,2.313 4.885,2.5 0.188,0.188 10 false 40 4.677,2.708 4.865,2.896 0.188,0.188 10 false 12 4.646,0.344 5.063,0.552 0.417,0.208 10 false F82 4.656,1.313 5.073,1.521 0.417,0.208 10 false F77 4.667,1.708 5.083,1.917 0.417,0.208 10 false F77 4.656,2.104 5.073,2.313 0.417,0.208 10 false F77 4.667,2.5 5.083,2.708 0.417,0.208 10 false F77 4.656,2.896 5.073,3.104 0.417,0.208 10 false F77 5.021,1.302 5.438,1.51 0.417,0.208 10 false CA+ 5.052,1.698 5.469,1.906 0.417,0.208 10 false V+ 5.052,2.104 5.469,2.313 0.417,0.208 10 false V- 5.042,2.5 5.625,2.708 0.583,0.208 10 false CGND 5.031,2.854 5.615,3.063 0.583,0.208 10 false GND1 1.708,2.51 2.292,2.719 0.583,0.208 10 false CGND 1.844,1.313 2.26,1.521 0.417,0.208 10 false CB+ 1.854,1.719 2.271,1.927 0.417,0.208 10 false CV+ 1.854,2.104 2.271,2.313 0.417,0.208 10 false CV- 0.688,2.75 1.104,2.958 0.417,0.208 10 false S5 0.688,2.917 2.844,3.146 2.156,0.229 10 false Rear Television Camera Assembly 4.979,3.135 6.375,3.542 1.396,0.406 10 false Multi-media Module Receiver Assembly 0.656,3.427 1.594,3.698 0.938,0.271 10 false : GVIF Cable

CAUTION / NOTICE / HINT

HINT:

Images may be unclear even in normal conditions if:

·

Noise may occur in the image depending on electrical devices used in the cabin.

·

Noise may occur in the image if accessories that generate radio waves have been installed.

·

The camera screen is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The ambient light surrounding the camera is too bright. (When a strong light, such as a sunbeam reflected off the vehicle body, hits the camera, the image may be blurred. This is called the "SMEAR" phenomenon, particular to the CCD camera.)

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER - REAR TELEVISION CAMERA AND BODY GROUND)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the S5 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-18 (V+) - S5-2 (CV+) Always Below 1 Ω
F77-19 (V-) - S5-1 (CV-) Always Below 1 Ω
F77-39 (CA+) - S5-4 (CB+) Always Below 1 Ω
F77-40 (CGND) - S5-3 (CGND) Always Below 1 Ω
F77-12 (GND1) - Body ground Always Below 1 Ω
F77-18 (V+) - Body ground Always 10 kΩ or higher
F77-19 (V-) - Body ground Always 10 kΩ or higher
F77-39 (CA+) - Body ground Always 10 kΩ or higher
F77-40 (CGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK MULTI-MEDIA MODULE RECEIVER DISPLAY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MULTI-MEDIA MODULE RECEIVER DISPLAY (CA+, CGND)
a.
U166323E02
2.552,1.146 2.635,1.698 2.635,1.698 2.854,1.698 true 2.635,1.146 2.813,1.385 2.813,1.385 3.031,1.385 true 0.073,0.052 0.375,0.292 0.302,0.24 10 false *a 1.573,0.125 1.885,0.292 0.313,0.167 10 false F77 3.073,1.302 3.396,1.542 0.323,0.24 10 false CA+ 2.885,1.615 3.385,1.896 0.5,0.281 10 false CGND

Reconnect the multi-media module receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-40 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F77-39 (CA+) - F77-40 (CGND) Engine switch on (IG), shift lever in R 5.5 to 7.05 V



Text in Illustration
*a Component with harness connected
(Multi-media Module Receiver Assembly)


OK

3.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

3.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)
a.

Reconnect the S5 rear television camera assembly connector.


U166351E02
3.792,1.563 4.094,1.969 4.094,1.969 4.271,1.969 false 3.677,1.604 3.74,2.115 3.74,2.115 3.875,2.115 false 2.417,1.167 2.604,0.927 2.604,0.927 2.74,0.927 true 2.333,1.292 2.594,1.604 2.594,1.604 2.729,1.604 true 6.01,1.406 6.344,1.969 6.344,1.969 6.521,1.969 false 5.896,1.469 5.99,2.125 5.99,2.125 6.125,2.125 false 5.281,0.083 5.563,0.333 0.281,0.25 10 false *c 3.146,0.094 3.396,0.323 0.25,0.229 10 false *b 0.125,0.083 0.531,0.385 0.406,0.302 10 false *a 4.313,1.906 4.49,2.083 0.177,0.177 10 false *e 3.906,2.042 4.073,2.219 0.167,0.177 10 false *d 6.594,1.906 6.771,2.083 0.177,0.177 10 false *e 6.177,2.042 6.344,2.219 0.167,0.177 10 false *d 5.063,1.052 5.438,1.323 0.375,0.271 10 false GND 2.917,1.063 3.323,1.323 0.406,0.26 10 false GND 1.313,0.24 1.646,0.479 0.333,0.24 10 false F77 2.781,0.844 3.01,1.021 0.229,0.177 10 false V+ 2.781,1.542 3.281,1.792 0.5,0.25 10 false CGND

Text in Illustration
*a Component with harness connected
(Multi-media Module Receiver Assembly)
*b Waveform A
*c Waveform B *d Synchronization Signal
*e Video Waveform - -

b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:
·

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.

·

The video waveform changes according to the image sent by the rear television camera assembly.



Measurement Condition
Item Content
Tester No. (Symbol) F77-18 (V+) - F77-40 (CGND)
Tool Setting 0.2 V/DIV., 50 μS/DIV
Condition Waveform A: Engine starts, shift lever in R (camera lens is not covered, displaying an image)
Waveform B: Engine starts, shift lever in R (camera lens is covered, blacking out the screen)

OK:

Waveform is as shown in the illustration.




OK

4.REPLACE HARNESS AND CONNECTOR (GVIF CABLE)

NG

4.REPLACE HARNESS AND CONNECTOR (GVIF CABLE)
a.

Replace the harness and connector (GVIF cable) with a normally functioning one.



NEXT

5.CHECK REAR VIEW MONITOR SYSTEM
5.CHECK REAR VIEW MONITOR SYSTEM
a.

Check the operation of rear view monitor system.

OK:

Rear view monitor system is operated normally.




OK

END (GVIF CABLE IS DEFECTIVE)

NG

6.REPLACE MULTI-DISPLAY ASSEMBLY
6.REPLACE MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).



NEXT

7.CHECK REAR VIEW MONITOR SYSTEM
7.CHECK REAR VIEW MONITOR SYSTEM
a.

Check the operation of rear view monitor system.

OK:

Rear view monitor system is operated normally.




OK

END (MULTI-DISPLAY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY