Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255506 PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System) J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)  "Back Door is Open" is Displayed even after Back Door is Closed  


DESCRIPTION

The multi-media module receiver assembly receives luggage compartment door lock assembly open/close signals from the main body ECU (cowl side junction block LH) via CAN communication. When the luggage compartment door is open, the camera aiming cannot be adjusted correctly because the rear television camera assembly is installed on the luggage compartment door. Therefore, when adjusting the camera aiming calibration while the back door is open, a back door open warning message will be displayed on the screen and camera aiming adjustment will be canceled.

HINT:

The back door lock assembly is connected to the main body ECU (cowl side junction block LH) by the vehicle wire harness.


WIRING DIAGRAM

E349803E02
0.719,0.344 0.875,0.542 0.156,0.198 10 false 1 1.865,0.344 2.021,0.542 0.156,0.198 10 false 3 2.323,0.344 2.479,0.542 0.156,0.198 10 false *1 3.313,0.344 3.5,0.563 0.188,0.219 10 false 25 0.75,0.781 0.938,1 0.188,0.219 10 false S1 3.156,0.917 3.406,1.135 0.25,0.219 10 false E2 2.323,1.906 2.479,2.104 0.156,0.198 10 false *2 1.854,1.917 2.01,2.115 0.156,0.198 10 false 3 0.74,1.917 0.958,2.156 0.219,0.24 10 false 4 0.656,2.302 1.021,2.521 0.365,0.219 10 false S22 0.75,0.969 2.531,1.271 1.781,0.302 10 false Back Door Lock Assembly 3.167,1.083 4.969,1.5 1.802,0.417 10 false Main Body ECU (Cowl Side Junction Block LH) 5.292,2.75 6.573,3.177 1.281,0.427 10 false Multi-media Module Receiver Assembly 0.656,2.458 2.594,2.698 1.938,0.24 10 false Back Door Lock Assembly 0.656,3.031 2.594,3.271 1.938,0.24 10 false :CAN Communication Line 0.073,3.375 2.396,3.594 2.323,0.219 10 false *1: w/o Power Back Door System 2.573,3.375 4.896,3.594 2.323,0.219 10 false *2: w/ Power Back Door System 0.917,0.438 1.281,0.646 0.365,0.208 10 false ACT- 3.563,0.448 4.146,0.719 0.583,0.271 10 false BCTY 1.677,0.438 1.865,0.656 0.188,0.219 10 false + 1.49,2.01 1.854,2.219 0.365,0.208 10 false CTY 0.917,2.01 1.281,2.219 0.365,0.208 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the multi-media module receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system (w/o Side Monitor System) may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)>CALIBRATION).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BACK DOOR COURTESY SWITCH)
a.

Use the Data List to check if the door lock positions are functioning properly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy switch signal / ON or OFF ON: Back door courtesy switch on
OFF: Back door courtesy switch off
-

OK:

The back door courtesy switch functions as specified in the normal condition column.




OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH] AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH] AND BODY GROUND)
a.

Disconnect the S1*1 or S22*2 back door lock assembly connector.

*1: w/o Power Back Door System

*2: w/ Power Back Door System



b.

Disconnect the E2 main body ECU (cowl side junction block LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Power Back Door System:
Tester Connection Condition Specified Condition
S1-3 (+) - E2-25 (BCTY) Always Below 1 Ω
S1-3 (+) - Body ground Always 10 kΩ or higher
S1-1 (ACT-) - Body ground Always Below 1 Ω

w/ Power Back Door System:
Tester Connection Condition Specified Condition
S22-3 (CTY) - E2-25 (BCTY) Always Below 1 Ω
S22-4 (E) - Body ground Always 10 kΩ or higher
S22-3 (CTY) - Body ground Always Below 1 Ω




OK

3.INSPECT BACK DOOR LOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Inspect the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION).



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPLACE BACK DOOR LOCK ASSEMBLY