Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › WIDE VIEW FRONT MONITOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255510 WIDE VIEW FRONT MONITOR SYSTEM J

PARK ASSIST / MONITORING  WIDE VIEW FRONT MONITOR SYSTEM  Image from Camera for Wide View Front Monitor is Abnormal  


DESCRIPTION

The display signal of the front television camera assembly is transmitted to the parking assist ECU.

WIRING DIAGRAM

E240589E12
5.021,1.313 5.458,1.542 0.438,0.229 10 false BCB+ 5.021,0.333 5.396,0.604 0.375,0.271 10 false GVIF 1.781,0.323 2.198,0.594 0.417,0.271 10 false GVIF 4.698,1.115 4.896,1.271 0.198,0.156 10 false 11 5.021,1.708 5.469,1.917 0.448,0.208 10 false BCV+ 4.698,1.521 4.896,1.677 0.198,0.156 10 false 12 5.021,2.104 5.479,2.323 0.458,0.219 10 false BCV- 4.708,1.917 4.906,2.073 0.198,0.156 10 false 36 5.021,2.5 5.5,2.698 0.479,0.198 10 false BGND 1.75,1.302 2.135,1.531 0.385,0.229 10 false BCB+ 1.76,1.698 2.167,1.917 0.406,0.219 10 false BCV+ 1.76,2.094 2.177,2.313 0.417,0.219 10 false BCV- 1.74,2.49 2.208,2.698 0.469,0.208 10 false BGND 4.708,2.313 4.906,2.469 0.198,0.156 10 false 35 2.219,1.219 2.323,1.375 0.104,0.156 10 false 1 2.219,1.615 2.323,1.771 0.104,0.156 10 false 2 2.219,2.01 2.323,2.167 0.104,0.156 10 false 4 2.219,2.406 2.323,2.563 0.104,0.156 10 false 3 5.021,2.885 5.469,3.094 0.448,0.208 10 false GND1 4.99,3.177 6.24,3.49 1.25,0.313 10 false Parking Assist ECU 0.646,2.729 1,2.948 0.354,0.219 10 false A55 0.635,2.885 2.844,3.208 2.208,0.323 10 false Front Television Camera Assembly 1.125,0.677 1.51,0.833 0.385,0.156 10 false F89 1.125,0.823 2.646,1.094 1.521,0.271 10 false Multi-display Assembly 0.646,3.438 1.708,3.74 1.063,0.302 10 false : GVIF Cable 4.729,2.708 4.854,2.865 0.125,0.156 10 false 4 4.667,2.896 5,3.094 0.333,0.198 10 false F75 4.667,2.51 4.958,2.688 0.292,0.177 10 false F76 4.667,2.115 4.958,2.323 0.292,0.208 10 false F76 4.667,1.719 4.979,1.958 0.313,0.24 10 false F76 4.667,1.323 4.958,1.531 0.292,0.208 10 false F76 4.75,0.125 4.844,0.281 0.094,0.156 10 false 1 2.229,0.208 2.479,0.365 0.25,0.156 10 false 1 4.656,0.344 4.938,0.542 0.281,0.198 10 false F88

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as wide view front monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).



HINT:

Images are difficult to discern even in normal conditions if:

·

Noise may occur in the image depending on electrical devices used in the cabin.

·

Noise may occur in the image if accessories that generate radio waves have been installed.

·

The camera screen is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The ambience of the camera is too bright. (When a strong light, such as a sunbeam reflected off the vehicle body, hits the camera, the image may be blurred. This is called the "SMEAR" phenomenon, particular to the CCD camera.)



PROCEDURE

1.CHECK SIDE MONITOR SYSTEM
a.

Check if the same malfunction occurs when the side monitor screen is displayed.

Result
Result Proceed to
Malfunction occurs when front monitor screen is displayed (side monitor screen is normal). A
Malfunction occurs when front assist monitor screen and side monitor screen are displayed. B



A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY AND BODY GROUND)

OK

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

OK

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

OK

5.CHECK HARNESS AND CONNECTOR (GVIF CABLE)

NG

5.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.

Replace GVIF cable with a normally functioning one.


b.

Check if the same malfunction recurs when the front monitor and side monitor screens are displayed.

OK:

Malfunction does not reoccur (returns to normal).




OK

END (GVIF CABLE IS DEFECTIVE)

NG

6.CHECK MULTI-DISPLAY ASSEMBLY
6.CHECK MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).


b.

Check if the same malfunction recurs when the front monitor and side monitor screens are displayed.

OK:

Malfunction does not reoccur (returns to normal).




OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG