SIDE MONITOR DIAGNOSIS SYSTEM
For side monitor system diagnosis, signals received by the parking assist ECU can be checked and the side monitor system can be calibrated, adjusted and checked using the multi-display assembly.
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>CALIBRATION).
The displayed screens and items may differ depending on vehicle specifications.
DIAGNOSIS SCREEN TRANSITION (during parking assist ECU initialization)
DIAGNOSIS SCREEN TRANSITION (after parking assist ECU initialization)
DIAGNOSTIC MODE
Start diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
Failure diagnosis (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
System check (check using system check mode screen) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
Finish diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
SIGNAL CHECK (parking assist ECU input signal)
Start diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
Select "Function Check/Setting" on the [Service Menu screen] to display the Function Check/Setting screen.
Select "Camera Setting" on the [Function Check/Setting] screen.
After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.
| Parking Assist ECU Initialization | Screen Transition |
|---|---|
| Not performed | [Signal Check] screen |
| Performed | [Mode Setting] screen |
When the screen changes to the [Mode Setting] screen, select "Back Camera Setting" to display the [Signal Check] screen.
To select a grayed out item, select and hold the item for 2 seconds or more.
SIGNAL CHECK
On the [Signal Check] screen, it is possible to inspect the state of signals sent to the parking assist ECU and check the settings.
| Item | Inspection Detail | Note |
|---|---|---|
| CAN | Speed signal input | When "CHK" (red) is displayed, selecting "Next" will not change to the next screen. |
| CAMERA SW | Front and side monitor main switch signal input | |
| MIRROR SW | Outer rear view mirror retract signal input | |
| VGRS* | VGRS signal input | |
| D-CAM SET | Driver side camera information signal input | - |
| OTA | Off-road turn assist function information input | - |
| DEST | Destination code signal input | - |
*1: w/ Variable Gear Ration Steering System
When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.
If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".
CAN inspection:
If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DTC CHECK / CLEAR).
CAMERA SW inspection:
Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".
Check that "OK" (blue) changes to "CHK" (red). Press the front and side monitor main switch assembly and check that "CHK" (red) returns to "OK" (blue).
If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the [Signal Check] screen) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.).
MIRROR SW inspection:
Check that "OK" (blue) is displayed for "MIRROR SW" and select "OK".
Check that "OK" (blue) changes to "CHK" (red). Press the outer mirror switch and check that "CHK" (red) returns to "OK" (blue).
After operating the outer mirror retract switch, if the outer mirror remains in the retracted state, return the outer mirror to the driving position. If "CHK" (red) remains displayed or the "MIRROR SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the [Signal Check] screen) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.)
VGRS inspection (w/ Variable Gear Ratio Steering System):
If "CHK" (red) is displayed for "VGRS", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>DIAGNOSTIC TROUBLE CODE CHART).
D-CAM SET inspection
Check that "WITH" (blue) is displayed for "D-CAM SET".
OTA inspection
Check that displayed for "OTA" is matched off-road turn assist function for vehicles.
DEST inspection
Check that displayed for "DEST" is matched destination code for vehicles.
Finish diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
CALIBRATION WHEN SERVICING VEHICLE
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>CALIBRATION).