Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › SIDE MONITOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255511 SIDE MONITOR SYSTEM J

PARK ASSIST / MONITORING  SIDE MONITOR SYSTEM  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the [Signal Check] screen, it is possible to check if the state of signals sent to the parking assist ECU is normal (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DIAGNOSIS SYSTEM).

HINT:
·

On the [Signal Check] screen, "OK" (blue) is displayed for items with a normal inspection result and input state.

·

On the [Signal Check] screen, "CHK" (red) is displayed for items with an abnormal inspection result and input state.

·

Displayed items may differ depending on the specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed
CAN CAN communication Speed signal input DTC is output
CAMERA SW Vehicle wire harness Front and side monitor main switch signal input DTC is not output
MIRROR SW Vehicle wire harness Outer rear view mirror retract signal input DTC is not output
VGRS CAN communication VGRS signal input DTC is output
D-CAM SET Vehicle wire harness Driver side camera information signal input DTC is not output
OTA Vehicle wire harness Off-road turn assist function information signal input DTC is not output
DEST Vehicle wire harness Destination code signal input DTC is not output

WIRING DIAGRAM

U166347E01
0.106,0.709 1.485,0.895 1.379,0.186 10 from IG1 NO. 1 Relay 1.76,0.871 2.652,1.023 0.892,0.151 10 ECU-IG No. 1 3.25,1.845 3.351,1.989 0.100,0.143 10 5 4.448,1.845 4.548,1.989 0.100,0.143 10 6 2.998,2.226 3.303,2.380 0.306,0.154 10 G16 2.998,2.376 4.885,2.525 1.887,0.149 10 Outer Mirror Switch Assembly 3.249,0.635 3.350,0.779 0.100,0.143 10 6 4.448,0.635 4.548,0.779 0.100,0.143 10 9 2.986,1.018 3.349,1.172 0.363,0.154 10 G15 2.986,1.18 4.763,1.515 1.776,0.335 10 Front and Side Monitor Main Switch Assembly 5.675,1.709 5.774,1.863 0.099,0.153 10 5 5.927,1.921 6.354,2.067 0.427,0.146 10 MPOS 5.591,1.917 5.860,2.063 0.269,0.146 10 F75 5.591,0.718 5.860,0.864 0.269,0.146 10 F76 5.703,0.493 5.885,0.646 0.182,0.153 10 7 5.927,0.711 6.354,0.858 0.427,0.146 10 BLSW 1.854,3.279 2.894,3.441 1.040,0.162 10 Steering Sensor 4.179,4.185 5.602,4.340 1.423,0.156 10 Steering Control ECU* 1.451,4.214 3.334,4.568 1.883,0.354 10 Master Cylinder Solenoid (Skid Control ECU Assembly) 3.834,5.293 5.798,5.506 1.964,0.213 10 Four Wheel Drive Control ECU 0.797,5.986 2.510,6.148 1.713,0.162 10 : CAN Communication Line 0.147,6.361 2.754,6.523 2.607,0.162 10 *: w/ Variable Gear Ratio Steering System 5.766,5.912 7.007,6.086 1.242,0.174 10 Parking Assist ECU 3.397,0.809 3.578,0.951 0.181,0.142 10 IG 4.081,0.809 4.397,0.952 0.317,0.143 10 ECU 3.392,1.922 3.505,2.077 0.113,0.154 10 E 4.156,1.922 4.400,2.072 0.244,0.149 10 MR 2.157,5.255 2.544,5.418 0.387,0.163 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the display and navigation module display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E252019

Check which items display "CHK" (red) on the [Signal Check] screen.

Result
Result Proceed to
"CAMERA SW" and "WFS SET" displays "CHK" (red). A
"MIRROR SW" displays "CHK" (red). B
"VGRS" displays "CHK" (red). C
"CAN" displays "CHK" (red). D



A

2.INSPECT FRONT AND SIDE MONITOR MAIN SWITCH ASSEMBLY

B

4.INSPECT OUTER MIRROR SWITCH ASSEMBLY

C

2.INSPECT FRONT AND SIDE MONITOR MAIN SWITCH ASSEMBLY
a.

Remove the front and side monitor main switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>FRONT AND SIDE MONITOR MAIN SWITCH>REMOVAL).


b.

Inspect the front and side monitor main switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>FRONT AND SIDE MONITOR MAIN SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (FRONT AND SIDE MONITOR MAIN SWITCH ASSEMBLY - PARKING ASSIST ECU, BATTERY AND BODY GROUND)

NG

REPLACE FRONT AND SIDE MONITOR MAIN SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FRONT AND SIDE MONITOR MAIN SWITCH ASSEMBLY - PARKING ASSIST ECU, BATTERY AND BODY GROUND)
a.

Disconnect the G15 front and side monitor main switch assembly connector.


b.

Disconnect the F76 parking assist ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G15-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G15-6 (IG) - Body ground Engine switch off Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-7 (BLSW) - G15-9(ECU) Always Below 1 Ω
G15-9 (ECU) - Body ground Always 10 kΩ or higher
G15-6 (IG) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.

Remove the outer mirror switch assembly (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL).


b.

Inspect the outer mirror switch assembly (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - PARKING ASSIST ECU)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the F75 parking assist ECU connector.


b.

Disconnect the G16 outer mirror switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F75-5 (MPOS) - G16-6 (MR) Always Below 1 Ω
F75-5 (MPOS) - Body ground Always 10 kΩ or higher
G16-5 (E) - Body ground Always Below 1 Ω




OK

6.CHECK POWER MIRROR CONTROL SYSTEM (POWER RETRACT FUNCTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER MIRROR CONTROL SYSTEM (POWER RETRACT FUNCTION)
a.

Check the power mirror control system (power retract function) (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>OPERATION CHECK).

OK:

Power mirror control system (power retract function) is normal.




OK

NG