DTC C1686 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly (for Driver Side) to the parking assist ECU.
DTC C1687 is stored if the parking assist ECU judges as a result off its self check that there is a problem with the current supplied from the side television camera assembly (for Driver Side) connected to the parking assist ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1686 | Side Camera Feedback Malfunction | ·
Harness or connector ·
Parking assist ECU ·
Side television camera assembly (for Driver Side) ·
Outer rear view mirror assembly (for Driver Side) |
| C1687 | Side Camera Current Malfunction |
When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>CALIBRATION).
Disconnect the F75 and F76 parking assist ECU connectors.
Disconnect the I35*1 or I32*2 outer rear view mirror assembly (for Driver Side) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-31 (DCV-) - I35-12 (DCV-) | Always | Below 1 Ω |
| F76-30 (DCV+) - I35-1 (DCV+) | Always | Below 1 Ω |
| F76-29 (DGND) - I35-13 (DGND) | Always | Below 1 Ω |
| F76-28 (DCB+) - I35-2 (DCB+) | Always | Below 1 Ω |
| F75-4 (GND1+) - Body ground | Always | Below 1 Ω |
| F76-31 (DCV-) - Body ground | Always | 10 kΩ or higher |
| F76-30 (DCV+) - Body ground | Always | 10 kΩ or higher |
| F76-29 (DGND) - Body ground | Always | 10 kΩ or higher |
| F76-28 (DCB+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-31 (DCV-) - I32-12 (SCV-) | Always | Below 1 Ω |
| F76-30 (DCV+) - I32-1 (SCV+) | Always | Below 1 Ω |
| F76-29 (DGND) - I32-13 (SGND) | Always | Below 1 Ω |
| F76-28 (DCB+) - I32-2 (SCB+) | Always | Below 1 Ω |
| F75-4 (GND1+) - Body ground | Always | Below 1 Ω |
| F76-31 (DCV-) - Body ground | Always | 10 kΩ or higher |
| F76-30 (DCV+) - Body ground | Always | 10 kΩ or higher |
| F76-29 (DGND) - Body ground | Always | 10 kΩ or higher |
| F76-28 (DCB+) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the F75 and F76 parking assist ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-29 (DGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F76-28 (DCB+) - F76-29 (DGND) | Engine switch on (IG), front and side monitor main switch assembly on | 5.5 to 7.05 V |
| *a | Component with harness connected
(Parking Assist ECU) |
OK
NG
Reconnect the I35*1 or I32*2 outer rear view mirror assembly (for Front Passenger Side) connector.
*1: for LHD
*2: for RHD
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
A waterproof connector is used for the side television camera assembly (for Driver Side). Therefore, inspect the waveform at the parking assist ECU with the connector connected.
The video waveform changes according to the image sent by the side television camera assembly (for Driver Side).
Measure the resistance according to the value(s) in the table below.
Waveform is as shown in the illustration.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F76-30 (DCV+) - F76-29 (DGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is not covered, displaying an image ·
Waveform B: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is covered, blacking out the screen |
OK
NG
Replace the side television camera assembly (for Driver Side) with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).
NEXT
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DTC CHECK / CLEAR).
DTC C1686 or C1687 is not output.
OK
NG