Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › 2015.08–2017.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255515 MULTI-TERRAIN MONITOR SYSTEM D

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  DIAGNOSIS SYSTEM  


MULTI-TERRAIN MONITOR DIAGNOSIS SYSTEM


a.

For multi-terrain monitor system diagnosis, signals received by the parking assist ECU can be checked, and the multi-terrain monitor system can be calibrated, adjusted and checked using the multi-display assembly*1 or radio and display receiver assembly*2.

*1: for Multi-media Module Receiver Type

*2: for Radio and Display Type


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>CALIBRATION).


HINT:

The displayed screens and items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (VIEW ADJUSTMENT)


E340086E01
2.823,0.896 4.302,1.146 1.479,0.25 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (STEERING ANGLE SETTING)


E340087E01
2.792,0.896 4.219,1.188 1.427,0.292 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (BODY COLOR SETTING)


E339655E03
2.813,0.896 4.49,1.313 1.677,0.417 10 false Start diagnostic mode



SIGNAL CHECK (parking assist ECU input signal)


a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E339651

Select "Camera Setting" on the "Function Check/Setting I" screen.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.


Parking Assist ECU Initialization Screen Transition
Not performed "Signal Check" screen
Performed "Mode Setting" screen


iii.
E296733

When the screen changes to the "Mode Setting" screen, select "View Adjustment" to display the "Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Signal check

i.
E340085

On the "Signal Check" screen, it is possible to inspect the state of signals sent to the parking assist ECU and check the settings.

Item Inspection Detail Note
CAN Speed signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
CAMERA SW Main switch assembly (multi-terrain monitor main switch) signal input
VGRS VGRS information input
OTA Off load turn assist function information input
VSC VSC information input

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).



d.

CAM CAN inspection

HINT:

If "CHK" (red) is displayed for "CAM CAN", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).



e.

CAMERA SW inspection

i.

Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".

HINT:

If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE).




f.

VGRS inspection

i.

Check that "OK" (blue) is displayed for "VGRS" and select "OK".

HINT:

If "CHK" (red) is displayed for "VGRS", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).




g.

VSC inspection

i.

Check that "WITH" (blue) or "WITHOUT" (blue) is displayed for "VSC" and select "WITH" or "WITHOUT".

HINT:

If "CHK" (red) remains displayed or the "VSC" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.).




h.

OTA inspection

i.

Check that "WITH" (blue) or "WITHOUT" (blue) is displayed for "OTA" and select "WITH" or "WITHOUT".

HINT:

If "CHK" (red) remains displayed or the "OTA" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.).






Body Color Setting


HINT:
·

This function is used for only customers who request it.

·

The color of the vehicle icon displayed on the moving view screen or the multi-terrain monitor screen can be changed from the diagnosis screen.




b.
E339651

Select "Camera Setting" on the "Function Check/Setting I" screen.


c.
E296733

Select "Body Color Setting" on the "Mode Setting" screen to display the "Body Color Setting" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



d.

Body color setting

i.
E334443

Select the color to change, and display the result confirm screen.

HINT:

White" is initialized.



ii.
E334444

Select "OK" on the result confirm screen, and display the mode setting screen.

NOTICE:

Changing the color of the icon may make the icon border hard to see on the moving view screen or multi-terrain monitor screen


HINT:
·

The body color setting screen does not display the actual body color.

·

To change the body color setting again, select "Back" and select it again.

·

The setting is memorized when the mode setting screen is displayed.

·
E339657

The tilt meter icon on the under floor view and two-side view screen does not change.







CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>CALIBRATION).