Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255515 MULTI-TERRAIN MONITOR SYSTEM J

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DIAGNOSIS SYSTEM).

HINT:
·

On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication signal DTC is not output Related ECUs
CAM CAN CAN communication CAN communication signal DTC is output
·

Front television camera assembly

·

Rear television camera assembly

·

Side television camera assembly LH

·

Side television camera assembly RH


CAMERA SW Vehicle wire harness Main switch assembly (multi-terrain monitor main switch) signal DTC is not output Main switch assembly (multi-terrain monitor main switch)
VGRS CAN communication VGRS information signal DTC is output Steering control ECU

WIRING DIAGRAM

E339652E02
2.332,0.912 2.743,1.087 0.411,0.175 10 E138 3.37,0.401 3.781,0.575 0.411,0.175 10 ECU 5.654,0.521 6.065,0.696 0.411,0.175 10 BLSW 5.434,0.426 5.599,0.601 0.165,0.175 10 7 3.746,0.426 3.910,0.601 0.165,0.175 10 7 2.364,0.426 2.528,0.601 0.165,0.175 10 1 1.625,0.657 2.753,0.831 1.129,0.175 10 ECU-IG NO.3 0.251,0.525 1.198,0.856 0.947,0.331 10 from IG1 NO.2 Relay 2.595,0.401 3.006,0.575 0.411,0.175 10 IG 2.332,1.069 4.579,1.448 2.247,0.380 10 Main Switch Assembly (Multi-terrain Monitor Mani Swich) 5.577,2.104 6.839,2.274 1.262,0.170 10 F76 5.577,2.267 6.839,2.437 1.262,0.170 10 Parking Assist ECU 0.81,2.384 2.811,2.554 2.002,0.170 10 : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the battery cable is disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E340085

Check which items display on the SIGNAL CHECK screen.

Result
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"CAN" or "VGRS" displays "CHK" (red) (for LHD with Central Gateway ECU) B
"CAN" or "VGRS" displays "CHK" (red) (for RHD with Central Gateway ECU) C
"CAM CAN" displays "CHK" (red) D



A

2.INSPECT MAIN SWITCH ASSEMBLY (MULTI-TERRAIN MONITOR MAIN SWITCH)

B

C

D

2.INSPECT MAIN SWITCH ASSEMBLY (MULTI-TERRAIN MONITOR MAIN SWITCH)
a.

Remove the main switch assembly (multi-terrain monitor main switch) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SWITCH>REMOVAL).


b.

Inspect the main switch assembly (multi-terrain monitor main switch) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (MAIN SWITCH ASSEMBLY [MULTI-TERRAIN MONITOR MAIN SWITCH] - PARKING ASSIST ECU AND BATTERY)

NG

REPLACE MAIN SWITCH ASSEMBLY (MULTI-TERRAIN MONITOR MAIN SWITCH)

3.CHECK HARNESS AND CONNECTOR (MAIN SWITCH ASSEMBLY [MULTI-TERRAIN MONITOR MAIN SWITCH] - PARKING ASSIST ECU AND BATTERY)
a.

Disconnect the E138 main switch assembly (multi-terrain monitor main switch) connector.


b.

Disconnect the F76 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E138-7 (ECU) - F76-7 (BLSW) Always Below 1 Ω
E138-7 (ECU) or F76-7 (BLSW) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E138-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V
E138-1 (IG) - Body ground Engine switch off Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR