Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255515 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.

DTC Code DTC Detection Condition Trouble Area
C1625 Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E349798E03
0.865,0.646 1.76,1.042 0.896,0.396 10 false from Steering Control ECU 0.375,1.208 1.865,1.458 1.49,0.25 10 false from IG1 NO. 3 Relay 2.073,1.396 3.052,1.656 0.979,0.26 10 false ECU-IG No. 1 3.229,0.667 3.719,0.906 0.49,0.24 10 false BAT 3.24,1.229 3.542,1.448 0.302,0.219 10 false IG 3.25,1.771 3.677,2.042 0.427,0.271 10 false ESS 3.104,2.24 3.594,2.479 0.49,0.24 10 false E163 3.104,2.406 4.344,2.604 1.24,0.198 10 false Steering Sensor 5.313,2.24 6.719,2.49 1.406,0.25 10 false Parking Assist ECU 3.052,0.573 3.26,0.76 0.208,0.188 10 false 5 3.052,1.115 3.26,1.302 0.208,0.188 10 false 4 3.063,1.677 3.271,1.865 0.208,0.188 10 false 1 1.115,2.979 2.969,3.219 1.854,0.24 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the battery terminal disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags.

Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

The multi-terrain monitor system troubleshooting procedure is based on the premise that the VGRS system is operating normally. Check the VGRS system first before troubleshooting the multi-terrain monitor system (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - BATTERY AND BODY GROUND)
a.
U166609E03
1.854,1.167 1.625,1.781 1.625,1.781 1.438,1.781 true 1.344,1.167 1.063,1.406 1.063,1.406 0.885,1.406 true 2.063,1.156 2.292,1.771 2.292,1.771 2.469,1.771 true 1.531,0.188 1.875,0.365 0.344,0.177 10 false E163 1.229,1.698 1.531,1.875 0.302,0.177 10 false IG 0.552,1.333 0.906,1.563 0.354,0.229 10 false ESS 2.542,1.698 2.896,1.906 0.354,0.208 10 false BAT 0.146,0.135 0.5,0.365 0.354,0.229 10 false *a

Disconnect the steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E163-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E163-4 (IG) - E163-1 (ESS) Engine switch on (IG) 11 to 14 V
E163-5 (BAT) - E163-1 (ESS) Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering sensor)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR