Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255516 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a +B short in the outer rear view mirror indicator RH.

DTC No. DTC Detection Condition Trouble Area
C1AB1 Both of the following conditions are met:
·

The blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on.


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.


·

Outer rear view mirror RH (outer rear view mirror indicator RH)

·

Outer rear view mirror assembly RH

·

Harness or connector

·

Blind spot monitor sensor RH

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

E329056E18
1.583,1.25 1.74,1.448 0.156,0.198 10 false 1 1.583,1.729 1.74,1.927 0.156,0.198 10 false 2 1.375,1.333 1.531,1.531 0.156,0.198 10 false + 1.375,1.802 1.531,2 0.156,0.198 10 false - 0.26,2.198 0.927,2.427 0.667,0.229 10 false IND1 0.26,2.344 2.313,2.74 2.052,0.396 10 false Outer Rear View Mirror RH (Outer Rear View Mirror Indicator RH) 0.177,3.604 2.51,3.854 2.333,0.25 10 false Outer Rear View Mirror Assembly LH 2.906,1.354 3.375,1.552 0.469,0.198 10 false I37 2.917,1.833 3.385,2.031 0.469,0.198 10 false I37 2.948,1.167 3.156,1.365 0.208,0.198 10 false 8 2.906,1.646 3.375,1.844 0.469,0.198 10 false 12 3.281,1.354 3.75,1.552 0.469,0.198 10 false BDIR 3.292,1.854 3.76,2.052 0.469,0.198 10 false HTR- 3.271,3.438 4.698,3.885 1.427,0.448 10 false Outer Mirror Control ECU Assembly LH 3.99,1.354 4.458,1.552 0.469,0.198 10 false BDSR 4.073,1.833 4.542,2.031 0.469,0.198 10 false GND 4.563,1.354 5.031,1.552 0.469,0.198 10 false I38 4.573,1.823 5.042,2.021 0.469,0.198 10 false I38 4.563,1.167 5.031,1.365 0.469,0.198 10 false 13 4.604,1.635 5.073,1.833 0.469,0.198 10 false 7 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIR 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.865,3.365 6.333,3.563 0.469,0.198 10 false r1 5.865,3.542 7.042,3.927 1.177,0.385 10 false Blind Spot Monitor Sensor RH 2.021,1.25 2.49,1.448 0.469,0.198 10 false BSR+ 2.292,1.74 2.448,1.938 0.156,0.198 10 false - 2.458,1.26 2.667,1.458 0.208,0.198 10 false 15 2.479,1.74 2.688,1.938 0.208,0.198 10 false 17 0.188,3.427 0.656,3.625 0.469,0.198 10 false I32

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on.


PROCEDURE

1.CHECK FOR DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR RH [OUTER REAR VIEW MIRROR INDICATOR RH])
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR RH [OUTER REAR VIEW MIRROR INDICATOR RH])
a.
U166396E01
1.642,0.297 1.919,0.498 0.276,0.201 10 r1 2.639,0.624 3.058,0.776 0.418,0.152 10 OMIR 0.118,0.079 0.395,0.280 0.276,0.201 10 *a 1.851,1.154 2.357,0.71 2.357,0.71 2.595,0.71 false

Disconnect the blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r1-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)



OK

NG

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.
U166396E01
1.642,0.297 1.919,0.498 0.276,0.201 10 r1 2.639,0.624 3.058,0.776 0.418,0.152 10 OMIR 0.118,0.079 0.395,0.280 0.276,0.201 10 *a 1.851,1.154 2.357,0.71 2.357,0.71 2.595,0.71 false

Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the IND1 outer rear view mirror RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r1-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)



OK

REPLACE OUTER REAR VIEW MIRROR RH

NG

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.
U166396E01
1.642,0.297 1.919,0.498 0.276,0.201 10 r1 2.639,0.624 3.058,0.776 0.418,0.152 10 OMIR 0.118,0.079 0.395,0.280 0.276,0.201 10 *a 1.851,1.154 2.357,0.71 2.357,0.71 2.595,0.71 false

Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the I32 outer rear view mirror assembly RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r1-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.
U166396E01
1.642,0.297 1.919,0.498 0.276,0.201 10 r1 2.639,0.624 3.058,0.776 0.418,0.152 10 OMIR 0.118,0.079 0.395,0.280 0.276,0.201 10 *a 1.851,1.154 2.357,0.71 2.357,0.71 2.595,0.71 false

Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the I37 outer mirror control ECU assembly RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r1-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.
U166396E01
1.642,0.297 1.919,0.498 0.276,0.201 10 r1 2.639,0.624 3.058,0.776 0.418,0.152 10 OMIR 0.118,0.079 0.395,0.280 0.276,0.201 10 *a 1.851,1.154 2.357,0.71 2.357,0.71 2.595,0.71 false

Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the I38 outer mirror control ECU assembly RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r1-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR