Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255516 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a ground short in the outer rear view mirror indicator LH.

DTC No. DTC Detection Condition Trouble Area
C1AB2 Both of the following conditions are met:
·

The blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on.


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time.


·

Outer rear view mirror LH (outer rear view mirror indicator LH)

·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E329056E17
1.563,1.74 1.719,1.938 0.156,0.198 10 false 1 1.563,1.26 1.719,1.458 0.156,0.198 10 false 2 1.365,1.354 1.521,1.552 0.156,0.198 10 false + 1.385,1.813 1.542,2.01 0.156,0.198 10 false - 0.25,2.198 0.813,2.406 0.563,0.208 10 false IND2 0.25,2.365 2.313,2.75 2.063,0.385 10 false Outer Rear View Mirror LH (Outer Rear View Mirror Indicator LH) 0.188,3.594 2.594,3.823 2.406,0.229 10 false Outer Rear View Mirror Assembly LH 2.896,1.354 3.365,1.552 0.469,0.198 10 false I40 2.052,1.25 2.521,1.448 0.469,0.198 10 false BSL+ 2.938,1.167 3.406,1.365 0.469,0.198 10 false 8 2.896,1.635 3.365,1.833 0.469,0.198 10 false 12 3.281,1.354 3.75,1.552 0.469,0.198 10 false BDIL 3.281,1.854 3.75,2.052 0.469,0.198 10 false HTR- 3.24,3.427 4.615,3.854 1.375,0.427 10 false Outer Mirror Control ECU Assembly LH 4.031,1.375 4.5,1.573 0.469,0.198 10 false BDSL 4.104,1.833 4.573,2.031 0.469,0.198 10 false GND 4.563,1.344 5.031,1.542 0.469,0.198 10 false I41 4.563,1.833 5.031,2.031 0.469,0.198 10 false I41 4.563,1.167 5.031,1.365 0.469,0.198 10 false 13 4.604,1.635 5.073,1.833 0.469,0.198 10 false 7 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIR 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.375 6.354,3.573 0.469,0.198 10 false r2 5.875,3.563 7.083,3.969 1.208,0.406 10 false Blind Spot Monitor Sensor LH 2.896,1.823 3.365,2.021 0.469,0.198 10 false I40 2.479,1.26 2.677,1.458 0.198,0.198 10 false 15 2.5,1.74 2.698,1.938 0.198,0.198 10 false 17 0.198,3.417 0.531,3.615 0.333,0.198 10 false I35 2.323,1.74 2.479,1.938 0.156,0.198 10 false -

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on.


PROCEDURE

1.CHECK FOR DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.
U166395E01
1.642,0.297 1.919,0.498 0.276,0.201 10 r2 2.639,0.624 3.058,0.776 0.418,0.152 10 OMIR 0.118,0.079 0.395,0.280 0.276,0.201 10 *a 1.851,1.154 2.357,0.71 2.357,0.71 2.595,0.71 false

Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the I40 outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r2-4 (OMIR) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)



OK

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.
U166386E01
1.667,0.196 1.950,0.354 0.283,0.158 10 I40 2.707,0.68 3.150,0.824 0.443,0.144 10 BDIL 0.198,0.075 0.367,0.231 0.170,0.156 10 *a 2.225,1.007 2.498,0.749 2.498,0.749 2.658,0.749 false

Disconnect the outer mirror control ECU assembly LH connector.


b.

Disconnect the I40 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I40-8 (BDIL) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)



OK

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
U166520E02
1.396,1.542 1.177,1.948 1.177,1.948 1,1.948 true 0.198,0.104 0.469,0.313 0.271,0.208 10 false *a 0.542,1.865 1.021,2.083 0.479,0.219 10 false BSL+ 1.604,0.229 1.875,0.438 0.271,0.208 10 false I35

Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the IND2 outer rear view mirror LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I35-15 (BSL+) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH)



OK

5.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.
U166472E02
2.135,1.302 2.229,1.771 2.229,1.771 2.396,1.771 true 1.927,1.104 1.51,1.844 1.51,1.844 1.323,1.844 true 0.115,0.135 0.385,0.344 0.271,0.208 10 false *a 0.938,1.75 1.406,1.958 0.469,0.208 10 false GND 2.469,1.688 2.938,1.896 0.469,0.208 10 false BDSL 2.313,0.198 2.583,0.406 0.271,0.208 10 false I41

Remove the outer mirror control ECU assembly LH connector (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I41-13 (BDSL) - I41-7 (GND) Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)



OK

6.CHECK OUTER REAR VIEW MIRROR LH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

6.CHECK OUTER REAR VIEW MIRROR LH
a.

Replace the outer rear view mirror LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR LH WAS DEFECTIVE)

NG