Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255516 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB4  Open in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No. DTC Detection Condition Trouble Area
C1AB4 Both of the following conditions are met:
·

The blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on.


·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator.


·

Outer rear view mirror LH (outer rear view mirror indicator LH)

·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E329056E17
1.563,1.74 1.719,1.938 0.156,0.198 10 false 1 1.563,1.26 1.719,1.458 0.156,0.198 10 false 2 1.365,1.354 1.521,1.552 0.156,0.198 10 false + 1.385,1.813 1.542,2.01 0.156,0.198 10 false - 0.25,2.198 0.813,2.406 0.563,0.208 10 false IND2 0.25,2.365 2.313,2.75 2.063,0.385 10 false Outer Rear View Mirror LH (Outer Rear View Mirror Indicator LH) 0.188,3.594 2.594,3.823 2.406,0.229 10 false Outer Rear View Mirror Assembly LH 2.896,1.354 3.365,1.552 0.469,0.198 10 false I40 2.052,1.25 2.521,1.448 0.469,0.198 10 false BSL+ 2.938,1.167 3.406,1.365 0.469,0.198 10 false 8 2.896,1.635 3.365,1.833 0.469,0.198 10 false 12 3.281,1.354 3.75,1.552 0.469,0.198 10 false BDIL 3.281,1.854 3.75,2.052 0.469,0.198 10 false HTR- 3.24,3.427 4.615,3.854 1.375,0.427 10 false Outer Mirror Control ECU Assembly LH 4.031,1.375 4.5,1.573 0.469,0.198 10 false BDSL 4.104,1.833 4.573,2.031 0.469,0.198 10 false GND 4.563,1.344 5.031,1.542 0.469,0.198 10 false I41 4.563,1.833 5.031,2.031 0.469,0.198 10 false I41 4.563,1.167 5.031,1.365 0.469,0.198 10 false 13 4.604,1.635 5.073,1.833 0.469,0.198 10 false 7 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIR 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.375 6.354,3.573 0.469,0.198 10 false r2 5.875,3.563 7.083,3.969 1.208,0.406 10 false Blind Spot Monitor Sensor LH 2.896,1.823 3.365,2.021 0.469,0.198 10 false I40 2.479,1.26 2.677,1.458 0.198,0.198 10 false 15 2.5,1.74 2.698,1.938 0.198,0.198 10 false 17 0.198,3.417 0.531,3.615 0.333,0.198 10 false I35 2.323,1.74 2.479,1.938 0.156,0.198 10 false -

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on.


PROCEDURE

1.CHECK FOR DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
a.

Disconnect the r2 blind spot monitor sensor LH connector.


b.

Disconnect the I41 outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r2-4 (OMIR) - I41-13 (BDSL) Always Below 1 Ω
I41-7 (GND) - Body ground Always Below 1 Ω




OK

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.
U166474E02
2.167,1.313 2.49,1.729 2.49,1.729 2.656,1.729 true 0.99,1.323 1.115,1.969 1.115,1.969 1.281,1.969 true 0.396,1.104 0.396,1.865 0.396,1.865 0.563,1.865 true 1.885,1.104 1.781,1.677 1.781,1.677 1.667,1.677 true 0.083,0.073 0.354,0.281 0.271,0.208 10 false *a 1.323,1.594 1.792,1.802 0.469,0.208 10 false GND 2.74,1.656 3.208,1.865 0.469,0.208 10 false BDSL 2.313,0.208 2.583,0.417 0.271,0.208 10 false I41 0.802,0.219 1.073,0.427 0.271,0.208 10 false I40 1.344,1.885 1.813,2.094 0.469,0.208 10 false HTR- 0.625,1.771 0.979,1.979 0.354,0.208 10 false BDIL

Remove the outer mirror control ECU assembly LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I41-13 (BDSL) - I40-8 (BDIL) Always Below 1 Ω
I41-7 (GND) - I40-12 (HTR-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)



OK

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the I40 outer mirror control ECU assembly LH connector.


b.

Disconnect the I35 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I40-8 (BDIL) - I35-15 (BSL+) Always Below 1 Ω
I40-12 (HTR-) - I35-17 (-) Always Below 1 Ω




OK

5.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the I35 outer rear view mirror assembly LH connector.


b.

Disconnect the IND2 outer rear view mirror LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I35-15 (BSL+) - IND2-2 (+) Always Below 1 Ω
I35-17 (-) - IND2-1 (-) Always Below 1 Ω




OK

6.CHECK OUTER REAR VIEW MIRROR LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

6.CHECK OUTER REAR VIEW MIRROR LH
a.

Replace the outer rear view mirror LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR LH WAS DEFECTIVE)

NG