Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255516 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABD  Short to +B in Buzzer  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

·

DTC C1ABD is stored when the blind spot monitor sensor RH detects a +B short in RCTA buzzer (blind spot monitor buzzer) circuit.

·

DTC C1ABE is stored when the blind spot monitor sensor RH detects a ground short or open in RCTA buzzer (blind spot monitor buzzer) circuit.


DTC No. DTC Detection Condition Trouble Area
C1ABD Both of the following conditions are met:
·

The blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on with the engine switch on (IG).

·

The blind spot monitor sensor is not sending voltage to the buzzer but the buzzer receives voltage above a specified level for a specified period of time.


·

Blind spot monitor sensor RH

·

RCTA buzzer (blind spot monitor buzzer)

·

Harness or connector


C1ABE Both of the following conditions are met:
·

The blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on with the engine switch on (IG).

·

The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer.


·

Blind spot monitor sensor RH

·

RCTA buzzer (blind spot monitor buzzer)

·

Harness or connector



WIRING DIAGRAM

E329058E05
0.135,1.042 1.49,1.24 1.354,0.198 10 false from IG1 NO. 2 Relay 3.479,0.927 3.771,1.125 0.292,0.198 10 false BZP 3.458,1.521 3.75,1.719 0.292,0.198 10 false L61 3.458,1.719 4.813,2.167 1.354,0.448 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.646,1.938 5.938,2.135 0.292,0.198 10 false r1 5.646,2.104 6.844,2.469 1.198,0.365 10 false Blind Spot Monitor Sensor RH 4.375,0.917 4.708,1.115 0.333,0.198 10 false BZN 3.302,0.906 3.448,1.083 0.146,0.177 10 false 1 5.656,1.021 5.99,1.219 0.333,0.198 10 false BUZ 5.448,0.927 5.594,1.104 0.146,0.177 10 false 3 4.729,0.917 4.875,1.094 0.146,0.177 10 false 2 2,1.188 3.021,1.385 1.021,0.198 10 false ECU-IG NO. 3

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot main switch (steering pad switch assembly [multi-function switch]) is on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK FOR DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect the L61 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the r1 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-2 (BZN) - r1-3 (BUZ) Always Below 1 Ω
L61-2 (BZN) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L61-1 (BZP) - Body ground Engine switch on (IG) 11 to 14 V
L61-1 (BZP) - Body ground Engine switch off Below 1 V




OK

3.REPLACE RCTA BUZZER (BLIND SPOT MONITOR BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE RCTA BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Replace the RCTA buzzer (blind spot monitor buzzer) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR CROSS TRAFFIC ALERT BUZZER>REMOVAL).



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] WAS DEFECTIVE)

NG