Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255517 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the multi-media module receiver assembly judges that the signals or signal lines between the rear television camera assembly, and the multi-media module receiver assembly are not normal as a result of its self check.

DTC Code Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Multi-media module receiver assembly



WIRING DIAGRAM

E329455E02
1.438,0.75 1.896,0.948 0.458,0.198 10 false CV- 1.427,1.26 1.885,1.458 0.458,0.198 10 false CV+ 1.427,1.76 1.885,1.958 0.458,0.198 10 false CB+ 1.333,2.271 1.792,2.469 0.458,0.198 10 false CGND 2.969,2.406 3.427,2.604 0.458,0.198 10 false * 3.479,2.406 3.938,2.604 0.458,0.198 10 false * 3.99,2.406 4.448,2.604 0.458,0.198 10 false * 4.479,2.406 4.938,2.604 0.458,0.198 10 false * 3.344,3.146 4.302,3.354 0.958,0.208 10 false *: Shielded 0.573,2.792 0.896,2.969 0.323,0.177 10 false S31 0.583,2.948 1.781,3.333 1.198,0.385 10 false Rear Television Camera Assembly 5.594,2.771 5.979,3.021 0.385,0.25 10 false F77 5.594,2.927 7.073,3.417 1.479,0.49 10 false Multi-media Module Receiver Assembly 5.385,0.646 5.625,0.802 0.24,0.156 10 false 19 5.396,1.135 5.635,1.292 0.24,0.156 10 false 18 5.417,1.656 5.688,1.865 0.271,0.208 10 false 39 5.417,2.125 5.635,2.344 0.219,0.219 10 false 40 5.688,0.75 6.052,1.021 0.365,0.271 10 false V- 5.677,1.229 6.052,1.479 0.375,0.25 10 false V+ 5.677,1.74 6.094,1.979 0.417,0.24 10 false CA+ 5.688,2.229 6.177,2.417 0.49,0.188 10 false CGND 1.844,0.635 2.302,0.833 0.458,0.198 10 false 2 1.844,1.146 2.302,1.344 0.458,0.198 10 false 3 1.833,1.635 2.167,1.833 0.333,0.198 10 false 6 1.854,2.146 2.188,2.344 0.333,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the multi-display after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the S31 rear television camera assembly connector.


b.

Disconnect the F77 multi-display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S31-6 (CB+) - F77-39 (CA+) Always Below 1 Ω
S31-3 (CV+) - F77-18 (V+) Always Below 1 Ω
S31-2 (CV-) - F77-19 (V-) Always Below 1 Ω
S31-5 (CGND) - F77-40 (CGND) Always Below 1 Ω
S31-6 (CB+) or F77-39 (CA+) - Body ground Always 10 kΩ or higher
S31-3 (CV+) or F77-18 (V+) - Body ground Always 10 kΩ or higher
S31-2 (CV-) or F77-19 (V-) - Body ground Always 10 kΩ or higher
S31-5 (CGND) or F77-40 (CGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
U166325E02
2.542,1.156 2.385,1.729 2.385,1.729 2.375,1.885 true 2.635,1.146 2.802,1.448 2.802,1.448 3.01,1.448 true 0.094,0.063 0.313,0.292 0.219,0.229 10 false *a 3.063,1.375 3.375,1.542 0.313,0.167 10 false CA+ 2.167,1.896 2.604,2.063 0.438,0.167 10 false CGND 1.583,0.125 1.958,0.375 0.375,0.25 10 false F77

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-40 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F77-39 (CA+) - F77-40 (CGND) Engine switch on (ACC) 5.5 to 7.05 V



Text in Illustration
*a Component with harness connected
(Multi-media Module Receiver Assembly)


OK

3.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

3.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.

Check the waveform of the rear television camera assembly using an oscilloscope.

U166558E02
0.594,1.833 0.979,1.281 true 1.906,1.333 2.104,1.833 true 3.167,1.823 2.99,2.323 true 3.271,1.74 3.396,2.333 true 5.719,1.698 5.521,2.229 true 5.833,1.646 5.948,2.24 false 1.094,0.448 1.542,0.667 0.448,0.219 10 false F77 2.51,1.365 2.958,1.594 0.448,0.229 10 false GND 5.031,1.365 5.479,1.594 0.448,0.229 10 false GND 0.333,0.229 0.552,0.448 0.219,0.219 10 false *a 2.948,0.292 3.167,0.51 0.219,0.219 10 false *b 5.479,0.292 5.698,0.51 0.219,0.219 10 false *c 2.906,2.323 3.125,2.542 0.219,0.219 10 false *d 3.333,2.344 3.552,2.563 0.219,0.219 10 false *e 5.438,2.281 5.656,2.5 0.219,0.219 10 false *d 5.896,2.229 6.115,2.448 0.219,0.219 10 false *e 2.063,1.865 2.396,2.094 0.333,0.229 10 false V+ 0.427,1.844 0.938,2.042 0.51,0.198 10 false GND1

Text in Illustration
*a Component with harness connected
(Multi-media Module Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the accessory meter assembly with the connector connected.

Item Content
Terminal No. (Symbol) F77-18 (V+) - F77-12 (GND1)
Tool setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image.
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen.


HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).



OK:

Waveform is as shown in the illustration.




OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG