Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on the "Bus Check" screen.

·

"Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside of combination meter assembly

·

Combination meter assembly



WIRING DIAGRAM

C175530E14
1.25,0.402 2.033,0.581 0.783,0.179 10 from Battery 1.091,1.109 2.050,1.318 0.959,0.210 10 from IG2 Relay 4.12,2.211 4.351,2.419 0.230,0.208 10 E7 4.12,2.376 5.963,2.562 1.842,0.186 10 Combination Meter Assembly 4.25,0.345 4.426,0.487 0.176,0.142 10 17 4.25,1.043 4.426,1.185 0.176,0.142 10 18 4.25,1.712 4.426,1.854 0.176,0.142 10 15 4.514,1.789 4.710,1.937 0.196,0.148 10 ET 4.514,1.128 4.774,1.276 0.260,0.148 10 IG+ 4.514,0.412 4.627,0.560 0.113,0.148 10 B 2.964,0.288 3.522,0.439 0.558,0.152 10 ECU-B1 3.083,0.97 3.410,1.122 0.327,0.152 10 MET

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)
a.
U166179E01
1.108,1.568 0.994,1.767 0.994,1.767 0.867,1.767 false 1.392,1.568 1.506,1.767 1.506,1.767 1.633,1.767 false 1.3,1.582 1.186,1.989 1.186,1.989 1.059,1.989 false 1.65,1.696 1.924,1.833 0.274,0.137 10 IG+ 0.617,1.696 0.890,1.833 0.274,0.137 10 ET 0.919,1.914 1.193,2.051 0.274,0.137 10 B 0.444,1.295 0.631,1.432 0.187,0.137 10 E7 0.077,0.052 0.351,0.189 0.274,0.137 10 *a

Disconnect the E7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-15 (ET) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-17 (B) - Body ground Always 11 to 14 V
E7-18 (IG+) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)

Result
Result Proceed to
OK (w/ Multi-information Display) A
OK (w/o Multi-information Display) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR