CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), COWL SIDE JUNCTION BLOCK LH
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH.
Reconnect the cowl side junction block LH connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-31 (BECU) - Body ground | - | Battery power supply | Always | Below 1 Ω |
| A-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| A-32 (IG) - Body ground | - | Ignition power supply (IG signal) | Ignition switch ON → Off | 11 to 14 V → Below 1 V |
| A-30 (ACC) - Body ground | - | ACC power supply | Ignition switch ACC → Off | 11 to 14 V → Below 1 V |
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Models with Jam Protection Function on 4 Windows)
Disconnect the I11*1 or I22*2 multiplex network master switch connector.
Measure the resistance and voltage according to the value(s) in the table below.
*1: for LHD
*2: for RHD
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I11-11 (B) - I11-12 (GND) | R - W-B | Ignition power supply | Ignition switch off | Below 1 Ω |
| I11-11 (B) - I11-12 (GND) | R - W-B | Ignition power supply | Ignition switch ON | 11 to 14 V |
| I11-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I22-11 (B) - I22-12 (GND) | R - W-B | Ignition power supply | Ignition switch off | Below 1 Ω |
| I22-11 (B) - I22-12 (GND) | R - W-B | Ignition power supply | Ignition switch ON | 11 to 14 V |
| I22-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)
Disconnect the I12 motor connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I12-2 (B) - I12-1 (GND) | L - W-B | Battery power supply | Always | 11 to 14 V |
| I12-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)
Disconnect the I4 motor connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I4-2 (B) - I4-1 (GND) | L - W-B | Battery power supply | Always | 11 to 14 V |
| I4-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)
Disconnect the J11 motor connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J11-2 (B) - J11-1 (GND) | L - W-B | Battery power supply | Always | 11 to 14 V |
| J11-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)
Disconnect the J4 motor connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J4-2 (B) - J4-1 (GND) | L - W-B | Battery power supply | Always | 11 to 14 V |
| J4-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (w/ Sliding Roof System)
Disconnect the R18 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R18-1 (B) - R18-12 (E) | LA-L - W-B | Battery power supply | Always | 11 to 14 V |
| R18-12 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
Disconnect the E130 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| E130-10 (+B) - E130-11 (E) | P - BR | Battery power supply | Always | 11 to 14 V |
| E130-11 (E) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Entry and Start System)
Disconnect the E124 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| E124-1 (+B) - E124-5 (GND) | W - BR | Battery power supply | Always | 11 to 14 V |
| E124-5 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
CHECK STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
Disconnect the E26 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| E26-7 (B) - E26-1 (GND) | G - W-B | Battery power supply | Always | 11 to 14 V |
| E26-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK AIR CONDITIONING AMPLIFIER (w/ Rear Heater)
Disconnect the E36 amplifier connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| E36-5 (IG+) - E36-1 (GND) | G - BR | IG power supply | Ignition switch off | Below 1 V |
| E36-5 (IG+) - E36-1 (GND) | G - BR | IG power supply | Ignition switch ON | 11 to 14 V |
| E36-6 (+B1) - E36-1 (GND) | LG - BR | Battery power supply | Always | 11 to 14 V |
| E36-7 (+B2) - E36-1 (GND) | LG - BR | Battery power supply | Always | 11 to 14 V |
| E36-1 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
CHECK AIR CONDITIONING AMPLIFIER (w/o Rear Heater)
Disconnect the E81 amplifier connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| E81-21 (+B1) - E81-14 (GND) | LG - BR | Battery power supply | Always | 11 to 14 V |
| E81-1 (IG+) - E81-14 (GND) | G - BR | IG power supply | Ignition switch ON | 11 to 14 V |
| E81-1 (IG+) - E81-14 (GND) | G - BR | IG power supply | Ignition switch off | Below 1 V |
| E81-14 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/o Entry and Start System)
Disconnect the F10 panel connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F10-7 (IG+) - F10-1 (GND) | B - W-B | IG power supply | Ignition switch ON | 11 to 14 V |
| F10-7 (IG+) - F10-1 (GND) | B - W-B | IG power supply | Ignition switch off | Below 1 V |
| F10-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/ Entry and Start System)
Disconnect the F111 panel connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F111-5 (IG+) - F111-8 (GND) | B - W-B | IG power supply | Ignition switch ON | 11 to 14 V |
| F111-5 (IG+) - F111-8 (GND) | B - W-B | IG power supply | Ignition switch off | Below 1 V |
| F111-8 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (w/ Rear Heater)
Disconnect the E55 panel connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| E55-6 (IG) - E55-1 (E) | B - W-B | IG power supply | Ignition switch ON | 11 to 14 V |
| E55-6 (IG) - E55-1 (E) | B - W-B | IG power supply | Ignition switch off | Below 1 V |
| E55-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
CHECK RAIN SENSOR (w/ Rain Sensor)
Disconnect the R11 rain sensor connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R11-4 (SIG) - Body ground | V - Body ground | IG power supply | Ignition switch off | Below 1 V |
| R11-4 (SIG) - Body ground | V - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| R11-2 (ES) - Body ground | W - Body ground | Ground circuit | Always | Below 1 V |
CHECK WINDSHIELD WIPER ECU (w/ Rain Sensor)
Disconnect the E147 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| E147-2 (IG) - E147-12 (E) | B - W-B | IG power supply | Ignition switch off | Below 1 V |
| E147-2 (IG) - E147-12 (E) | B - W-B | IG power supply | Ignition switch ON | 11 to 14 V |
| E147-12 (E) - Body ground | W-B - Body ground | Ground circuit | Always | Below 1 Ω |