Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2287  LIN Communication Master Malfunction  


DESCRIPTION

This DTC is stored there is an open, short or ECU communication malfunction between the main body ECU (cowl side junction block LH) and certification ECU (smart key ECU assembly).

DTC Code DTC Detection Condition Trouble Area
B2287 There is an open, short or ECU communication malfunction between the main body ECU (cowl side junction block LH) and certification ECU (smart key ECU assembly).
·

Certification ECU (smart key ECU assembly)

·

Main body ECU (cowl side junction block LH)

·

Harness or connector



WIRING DIAGRAM

B173732E02
0.733,3.505 1.431,3.674 0.698,0.170 10 : LIN Line 1.539,2.601 3.334,3.111 1.795,0.510 10 Main Body ECU (Cowl Side Junction Block LH) 2.337,1.802 2.688,1.972 0.350,0.170 10 LIN1 4.593,1.802 4.943,1.972 0.350,0.170 10 LIN 4.509,2.573 4.859,2.743 0.350,0.170 10 E29 2.719,1.807 2.955,1.977 0.236,0.170 10 2D 2.731,1.632 2.967,1.801 0.236,0.170 10 20 4.326,1.699 4.529,1.869 0.203,0.170 10 10 4.509,2.72 6.679,3.126 2.170,0.406 10 Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

When DTC B2287 and B2785 are output simultaneously, perform the troubleshooting for DTC B2785 first (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>B2785).


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2287 is output A
DTC B2287 is not output B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - MAIN BODY ECU)

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - MAIN BODY ECU)
U165866E02
2.323,1.604 2.438,1.604 2.438,1.604 2.906,1.177 false 5.26,1.552 5.375,1.552 5.375,1.552 5.906,1.104 false 0.646,0.052 2.979,0.552 2.333,0.5 10 false Front view of wire harness connector: (to Main Body ECU) 4.677,0.052 7,0.583 2.323,0.531 10 false Front view of wire harness connector: (to Certification ECU) 0.198,0.948 0.458,1.146 0.26,0.198 10 false 2D 2.01,1.542 2.385,1.708 0.375,0.167 10 false LIN1 5.01,1.479 5.385,1.646 0.375,0.167 10 false LIN 4.167,0.938 4.531,1.146 0.365,0.208 10 false E29

a.

Disconnect the E29 and 2D ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E29-10 (LIN) - 2D-20 (LIN1) Always Below 1 Ω
E29-10 (LIN) or 2D-20 (LIN1) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
E29-10 (LIN) or 2D-20 (LIN1) - Body ground Always Below 1 V




OK

4.REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
a.

Temporarily replace the main body ECU (cowl side junction block LH) with a new or normally functioning one.




NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2287 is not output A
DTC B2287 is output B



A

END (MAIN BODY ECU IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)