Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2324  Rear Door LH ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the rear power window regulator motor LH and main body ECU (cowl side junction block LH) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2324 No communication between the rear power window regulator motor LH and main body ECU (cowl side junction block LH) for 10 seconds or more.
·

Rear power window regulator motor LH

·

Main body ECU (cowl side junction block LH)

·

Harness or connector



WIRING DIAGRAM

U163928E02
1.99,2.24 2.125,2.271 0.135,0.031 0.938,4.719 1.604,4.917 0.667,0.198 10 false : LIN Line 0.594,3.875 1.448,4.073 0.854,0.198 10 false from Battery 1.688,4.021 2.677,4.219 0.99,0.198 10 false RR DOOR LH 3.448,4.292 3.802,4.469 0.354,0.177 10 false J11 3.354,3.75 3.51,3.927 0.156,0.177 10 false 2 3.354,2.99 3.51,3.167 0.156,0.177 10 false 9 3.313,1.146 3.5,1.323 0.188,0.177 10 false 10 3.563,3.135 4,3.313 0.438,0.177 10 false LIN 3.563,1.302 4,1.479 0.438,0.177 10 false LIN2 4.271,3.135 4.625,3.313 0.354,0.177 10 false GND 4.656,2.99 4.792,3.167 0.135,0.177 10 false 1 3.563,3.885 4,4.063 0.438,0.177 10 false B 3.448,4.469 6.156,4.646 2.708,0.177 10 false Rear Power Window Regulator Motor LH 3.5,1.896 3.771,2.073 0.271,0.177 10 false E3 3.5,2.063 5.156,2.521 1.656,0.458 10 false Main Body ECU (Cowl Side Junction Block LH)

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

DTC B2325 is stored when the communication between the rear power window regulator motor and main body ECU (cowl side junction block LH) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2324 is output A
DTC B2324 is not output B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR POWER WINDOW REGULATOR MOTOR LH)

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR POWER WINDOW REGULATOR MOTOR LH)
U165868E01
2.351,4.404 2.16,4.404 2.16,4.404 1.781,4.025 false 0.43,1.242 0.699,1.403 0.269,0.160 10 E3 0.412,3.619 0.680,3.779 0.269,0.160 10 J11 2.334,1.667 2.046,1.606 false 2.369,1.624 2.734,1.780 0.364,0.156 10 LIN2 0.172,0.02 2.585,0.488 2.413,0.468 10 Front view of wire harness connector: (to Main Body ECU) 0.056,2.144 2.743,2.660 2.687,0.516 10 Front view of wire harness connector: (to Rear Power Window Regulator Motor LH) 2.401,4.332 2.725,4.488 0.324,0.156 10 LIN

a.

Disconnect the E3 ECU connector.


b.

Disconnect the J11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-10 (LIN2) - J11-9 (LIN) Always Below 1 Ω
E3-10 (LIN2) or J11-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (BATTERY VOLTAGE AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (BATTERY VOLTAGE AND BODY GROUND)
a.
U163896E01
0.237,0.12 2.671,0.679 2.434,0.559 10 Front view of wire harness connector: (to Rear Power Window Regulator Motor LH) 0.571,1.916 0.864,2.079 0.292,0.163 10 J11 0.83,2.252 1.186,2.415 0.356,0.163 10 GND 2.125,2.307 2.302,2.470 0.177,0.163 10 B 1.526,2.174 1.23,2.312 false 1.861,2.17 2.119,2.303 false

Disconnect the J11 motor connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
J11-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
J11-2 (B) - Body ground Always 11 to 14 V




OK

5.REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Temporarily replace the rear power window regulator motor LH with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2324 is not output A
DTC B2324 is output B



A

END (REAR POWER WINDOW REGULATOR MOTOR LH IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)