Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2324  Rear Door LH ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the rear power window regulator motor LH and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2324 No communication between the rear power window regulator motor LH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Rear power window regulator motor LH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

E340193E04
0.593,6.34 2.208,6.521 1.615,0.181 10 : LIN Communication Line 4.297,3.809 4.622,3.990 0.326,0.181 10 GND 3.661,3.795 3.972,3.976 0.310,0.181 10 LIN 3.846,1.562 4.009,1.744 0.164,0.181 10 2J 3.661,4.318 3.817,4.499 0.156,0.181 10 B 5.861,0.974 6.171,1.155 0.310,0.181 10 LIN2 5.553,0.815 5.724,0.996 0.171,0.181 10 16 3.659,0.815 3.831,0.996 0.171,0.181 10 13 3.42,3.654 3.576,3.836 0.156,0.181 10 9 4.747,3.668 4.902,3.850 0.156,0.181 10 1 3.42,4.229 3.576,4.410 0.156,0.181 10 2 3.15,4.873 3.484,5.055 0.334,0.181 10 J11 5.584,2.864 6.772,3.446 1.187,0.582 10 Main Body ECU (Multiplex Network Body ECU) 0.98,4.316 2.058,4.583 1.078,0.267 10 from Battery 2.367,4.513 3.399,4.780 1.032,0.267 10 DOOR R/L 3.15,5.026 5.108,5.372 1.958,0.346 10 Rear Power Window Regulator Motor AssemblyLH 3.846,1.721 5.638,1.902 1.793,0.181 10 Cowl Side Junction Block LH 5.588,2.718 5.913,2.899 0.326,0.181 10 A

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

DTC B2325 is stored when the communication between the rear power window regulator motor LH and main body ECU (multiplex network body ECU) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2324 is output A
DTC B2324 is not output B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODYECU] - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODYECU] - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the A main body ECU connector.


b.

Disconnect the J11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - J11-9 (LIN) Always Below 1 Ω
A-16 (LIN2) or J11-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH BATTERY AND BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH))
4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH BATTERY AND BODY GROUND)
a.
U163872E02
1.521,1 0.885,1.292 false 1.927,0.979 2.458,1.292 false 0.083,0.021 0.323,0.24 0.24,0.219 10 false *a 0.563,0.719 0.854,0.885 0.292,0.167 10 false J11 0.521,1.229 0.906,1.427 0.385,0.198 10 false GND 2.521,1.219 2.698,1.385 0.177,0.167 10 false B

Disconnect the motor connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
J11-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
J11-2 (B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Rear Power Window Regulator Motor LH)



OK

5.REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Temporarily replace the rear power window regulator motor LH with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2324 is not output A
DTC B2324 is output (for LHD) B
DTC B2324 is output (for RHD) C



A

END (REAR POWER WINDOW REGULATOR MOTOR LH IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH))
a.

Disconnect the 2J cowl side junction block LH connector.


b.

Disconnect the J11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-13 - J11-9 (LIN) Always Below 1 Ω
2J-13 or J11-9 (LIN) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR