Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM J

NETWORKING  LIN COMMUNICATION SYSTEM  Rain Sensor LIN Communication Malfunction  


DESCRIPTION

The LIN communication of the components related to the rain sensor occurs between the rain sensor and windshield wiper ECU.

WIRING DIAGRAM

E334874E04
1.862,0.972 2.289,1.135 0.427,0.163 10 MPX1 2.341,0.86 2.584,1.016 0.243,0.156 10 14 0.981,1.573 1.476,1.743 0.495,0.170 10 E147 0.963,1.731 2.466,1.914 1.503,0.184 10 Windshield Wiper ECU 1.809,3.284 2.775,3.458 0.966,0.174 10 ECU-IG NO. 2 2.924,3.028 3.097,3.201 0.173,0.173 10 14 2.966,3.626 3.139,3.799 0.173,0.173 10 3 3.204,3.743 3.686,3.893 0.482,0.150 10 GND5 4.281,3.033 4.497,3.196 0.215,0.163 10 29 2.993,4.269 3.270,4.432 0.277,0.163 10 R7 4.331,3.645 4.511,3.782 0.180,0.137 10 4 5.296,3.03 5.403,3.200 0.107,0.170 10 4 3.789,3.743 4.257,3.926 0.468,0.184 10 GND2 3.924,3.122 4.233,3.278 0.309,0.156 10 IG2 3.233,3.122 3.437,3.278 0.204,0.156 10 IG 2.969,4.43 4.598,4.613 1.629,0.184 10 Overhead Junction Block 5.39,4.677 5.687,4.859 0.297,0.182 10 R11 5.397,4.839 6.227,5.036 0.830,0.198 10 Rain Sensor 5.465,3.743 5.718,3.899 0.253,0.156 10 ES 5.297,3.645 5.418,3.836 0.121,0.191 10 2 5.465,3.122 5.767,3.294 0.302,0.172 10 SIG 5.463,0.972 5.817,1.173 0.354,0.201 10 MPX 5.274,0.86 5.402,1.029 0.128,0.169 10 1 0.511,5.403 2.150,5.605 1.639,0.202 10 : LIN Communication Line 0.471,3.081 1.303,3.580 0.833,0.498 10 from IG1 NO.1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - WIND SHIELD WIPER ECU)
a.

Disconnect the E147 windshield wiper ECU connector.


b.

Disconnect the R11 rain sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R11-1 (MPX) - E1147-14 (MPX1) Always Below 1 Ω
R11-1 (MPX) - Body ground Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (RAIN SENSOR BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (RAIN SENSOR BATTERY AND BODY GROUND)
a.
U163874E01
2.208,1.476 2.638,1.674 0.430,0.198 10 SIG 1.167,1.511 1.597,1.709 0.430,0.198 10 ES 1.57,1.125 1.304,1.49 false 1.98,1.125 2.314,1.443 false 0.088,0.011 0.310,0.205 0.222,0.194 10 *a 1.584,0.307 1.878,0.501 0.295,0.194 10 R11

Disconnect the rain sensor connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R11-2 (ES) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
R11-4 (SIG) - Body ground Ignition switch off → Ignition switch ON Below 1 V → 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Rain Sensor)



OK

3.REPLACE RAIN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE RAIN SENSOR
a.

Temporarily replace the rain sensor with a new one (See page Vehicle Exterior>WIPER / WASHER>RAIN SENSOR>REMOVAL).


b.

Check the rain sensor function is normal.

OK:

Rain sensor function is normal.




OK

END (RAIN SENSOR IS DEFECTIVE)

NG

REPLACE WINDSHIELD WIPER ECU