There may be an open circuit in one of the bus 2 main lines and/or a central gateway ECU CAN branch wire when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU is 70 Ω or higher
| Detection Item | Trouble Area |
|---|---|
| Resistance between terminals 18 (CA4H) and 17 (CA4L) of central gateway ECU is 70 Ω or higher. | ·
Bus 2 CAN main wire or connector ·
Bus 2 CAN branch wire or connector ·
ECM ·
Combination meter assembly ·
Central gateway ECU ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector |
This malfunction is not related to the lines of a bus 2 branch except the central gateway ECU CAN branch wires or to ECUs or sensors connected a bus 2 branch.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-10 (CANH) - A38-11 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-41 (CANH) - A38-49 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-11 (CANH) - A38-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *A | for 1UR-FE, 1GR-FE |
| *B | for 1VD-FTV |
| *C | for 3UR-FE |
| *a | Front view of wire harness connector
(to ECM) |
| Result | Proceed to |
|---|---|
| OK (for 1UR-FE) | A |
| OK (for 1VD-FTV) | B |
| OK (for 1GR-FE) | C |
| OK (for 3UR-FE) | D |
| NG | E |
A
B
C
D
E
Reconnect the A38 ECM connector.
NEXT
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E119-39 (CANH) - E119-40 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
OK
NG
Reconnect the E119 combination meter assembly connector.
NEXT
Disconnect the central gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E145-18 (CA4H) - E145-17 (CA4L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Central Gateway ECU) |
OK
NG
Reconnect the E145 central gateway ECU connector.
NEXT
Disconnect the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | to ECM | *d | to Central Gateway ECU |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E135-1 (CANH) - E135-11 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| E135-7 (CANH) - E135-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| E135-9 (CANH) - E135-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM CAN main wire) | B |
| NG (Central gateway ECU CAN branch wire) | C |
| NG (No. 2 CAN junction connector CAN main wire) | D |
A
B
C
D
Reconnect the E135 No. 1 CAN junction connector.
NEXT
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to No. 1 CAN Junction Connector |
| *c | to Combination Meter Assembly | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E133-1 (CANH) - E133-11 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| E133-7 (CANH) - E133-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Combination meter assembly CAN main wire) | B |
| NG (No. 1 CAN junction connector CAN main wire) | C |
A
B
C