Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › 2015.08–2020.06
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 2 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 18 (CA4H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area
No resistance exists between terminal 18 (CA4H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU and terminal 4 (CG) of the DLC3.
·

Short to GND in bus 2 CAN main wires

·

Short to GND in bus 2 CAN branch wires

·

ECM

·

4WD control ECU

·

Power steering ECU assembly*1

·

Airbag sensor assembly

·

Tire pressure warning ECU*2

·

Air conditioning amplifier assembly

·

Central gateway ECU

·

Main body ECU (multiplex network body ECU)

·

Master cylinder solenoid (skid control ECU)

·

Headlight leveling ECU assembly

·

Certification ECU (smart key ECU assembly)*3

·

Steering control ECU*4

·

Steering sensor

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector



*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System

*3: w/ Entry and Start System

*4: w/ Variable Gear Ratio Steering System


WIRING DIAGRAM

C348515E01
6.179,1.699 6.539,1.848 0.361,0.149 10 A38 6.179,1.836 6.539,1.985 0.361,0.149 10 ECM 5.944,1.387 6.447,1.536 0.503,0.149 10 CANL 5.944,0.662 6.447,0.811 0.503,0.149 10 CANH 4.827,0.662 5.869,0.811 1.042,0.149 10 10*1, 41*2, 11*3 4.827,1.198 5.894,1.347 1.068,0.149 10 11*1, 49*2, 19*3 4.081,0.662 4.584,0.811 0.503,0.149 10 7 4.081,1.198 4.584,1.347 0.503,0.149 10 17 3.194,0.662 3.697,0.811 0.503,0.149 10 2 3.128,1.198 3.631,1.347 0.503,0.149 10 12 4.081,2.628 4.584,2.777 0.503,0.149 10 3 4.081,3.164 4.584,3.313 0.503,0.149 10 13 3.194,2.628 3.697,2.777 0.503,0.149 10 4 3.128,3.164 3.631,3.313 0.503,0.149 10 14 0.084,5.577 0.445,5.726 0.361,0.149 10 E35 0.084,5.718 1.703,6.065 1.619,0.348 10 Air Conditioning Amplifier Assembly 0.844,5.216 1.347,5.365 0.503,0.149 10 CANL 0.844,4.672 1.347,4.821 0.503,0.149 10 CANH 1.406,4.553 1.909,4.702 0.503,0.149 10 3 1.406,5.089 1.909,5.238 0.503,0.149 10 4 4.081,4.586 4.584,4.735 0.503,0.149 10 5 4.081,5.122 4.584,5.271 0.503,0.149 10 15 3.194,4.586 3.697,4.735 0.503,0.149 10 8 3.128,5.122 3.631,5.271 0.503,0.149 10 18 2.825,6.057 3.186,6.206 0.361,0.149 10 E135 2.825,6.193 5.113,6.342 2.288,0.149 10 No. 1 CAN Junction Connector 0.852,1.31 1.355,1.459 0.503,0.149 10 CANL 0.852,0.766 1.355,0.915 0.503,0.149 10 CANH 1.389,0.629 1.892,0.778 0.503,0.149 10 20 1.389,1.165 1.892,1.314 0.503,0.149 10 40 0.266,1.703 0.627,1.852 0.361,0.149 10 A27 0.266,1.839 1.985,1.988 1.718,0.149 10 4WD Control ECU 0.051,3.576 0.412,3.725 0.361,0.149 10 E47 0.051,3.713 1.735,4.060 1.684,0.348 10 Airbag Sensor Assembly 0.852,3.257 1.355,3.406 0.503,0.149 10 CANL 0.852,2.714 1.355,2.862 0.503,0.149 10 CANH 1.389,2.577 1.892,2.725 0.503,0.149 10 13 1.389,3.112 1.892,3.261 0.503,0.149 10 22 6.009,3.246 6.512,3.394 0.503,0.149 10 CANL 6.009,2.713 6.512,2.862 0.503,0.149 10 CANH 4.899,3.526 5.315,3.675 0.416,0.149 10 E102 4.899,3.662 7.071,3.981 2.172,0.318 10 Power Steering ECU Assembly*4 5.708,3.135 6.211,3.284 0.503,0.149 10 2 5.708,2.598 6.211,2.747 0.503,0.149 10 1 5.114,4.668 5.474,4.817 0.361,0.149 10 L65 5.114,5.2 5.474,5.349 0.361,0.149 10 L65 5.562,4.668 5.923,4.817 0.361,0.149 10 L75 5.562,5.2 5.923,5.349 0.361,0.149 10 L75 5.962,5.207 6.465,5.356 0.503,0.149 10 CANL 5.962,4.675 6.465,4.824 0.503,0.149 10 CANH 5.087,5.009 5.590,5.157 0.503,0.149 10 10*5 5.115,4.471 5.618,4.620 0.503,0.149 10 9*5 5.549,5.009 6.052,5.157 0.503,0.149 10 10*6 5.577,4.471 6.080,4.620 0.503,0.149 10 9*6 5.053,5.612 7.026,5.761 1.973,0.149 10 Tire Pressure Warning ECU*7 0.21,6.57 1.989,6.719 1.779,0.149 10 *1: for 1UR-FE, 1GR-FE 0.21,7.123 1.470,7.272 1.260,0.149 10 *3: for 3UR-FE 0.21,6.853 1.720,7.002 1.510,0.149 10 *2: for 1VD-FTV 0.21,7.378 3.544,7.527 3.334,0.149 10 *4: w/ Variable Flow Control Solenoid Valve 3.236,6.57 5.691,6.719 2.455,0.149 10 *5: w/o Front Antenna 3.236,6.853 5.691,7.002 2.455,0.149 10 *6: w/ Front Antenna 3.236,7.123 6.209,7.272 2.973,0.149 10 *7: w/ Tire Pressure Warning System

C348516E01
4.123,2.43 4.626,2.579 0.503,0.149 10 1 4.123,2.966 4.626,3.115 0.503,0.149 10 11 4.123,0.469 4.626,0.618 0.503,0.149 10 1 4.123,1.005 4.626,1.154 0.503,0.149 10 11 3.167,2.43 3.670,2.579 0.503,0.149 10 2 3.1,2.966 3.603,3.115 0.503,0.149 10 12 3.167,0.469 3.670,0.618 0.503,0.149 10 9 3.1,1.005 3.603,1.154 0.503,0.149 10 19 4.123,4.396 4.626,4.545 0.503,0.149 10 3 4.123,4.932 4.626,5.081 0.503,0.149 10 13 3.167,4.396 3.670,4.545 0.503,0.149 10 4 3.1,4.932 3.603,5.081 0.503,0.149 10 14 3.18,6.368 3.684,6.517 0.503,0.149 10 8 3.11,6.904 3.614,7.053 0.503,0.149 10 18 4.129,6.368 4.632,6.517 0.503,0.149 10 6 4.129,6.904 4.632,7.053 0.503,0.149 10 16 2.776,7.646 3.137,7.795 0.361,0.149 10 E133 2.776,7.783 4.719,7.932 1.943,0.149 10 No. 2 CAN Junction Connector 2.727,1.447 3.088,1.595 0.361,0.149 10 E135 2.727,1.583 5.135,1.732 2.408,0.149 10 No. 1 CAN Junction Connector 0.881,1.125 1.385,1.274 0.503,0.149 10 CA4L 0.881,0.579 1.385,0.728 0.503,0.149 10 CA4H 1.393,1.041 1.896,1.190 0.503,0.149 10 17 1.393,0.509 1.896,0.658 0.503,0.149 10 18 0.347,1.516 0.708,1.665 0.361,0.149 10 E145 0.347,1.652 2.191,1.801 1.843,0.149 10 Central Gateway ECU 0.865,3.05 1.369,3.199 0.503,0.149 10 CANL 0.865,2.503 1.369,2.652 0.503,0.149 10 CANH 1.377,2.966 1.880,3.115 0.503,0.149 10 13 1.377,2.433 1.880,2.582 0.503,0.149 10 14 0.253,3.442 0.771,3.591 0.518,0.149 10 E118 0.253,3.6 1.918,4.102 1.665,0.501 10 Main Body ECU (Multiplex Network Body ECU) 5.477,5.312 5.838,5.461 0.361,0.149 10 A24 5.477,5.449 7.124,5.796 1.647,0.348 10 Master Cylinder Solenoid (Skid Control ECU) 5.985,5.031 6.488,5.180 0.503,0.149 10 CANL 5.985,4.487 6.488,4.636 0.503,0.149 10 CANH 5.723,4.402 6.226,4.551 0.503,0.149 10 11 5.723,4.938 6.226,5.087 0.503,0.149 10 25 0.862,5.043 1.365,5.192 0.503,0.149 10 CANL 0.862,4.497 1.365,4.646 0.503,0.149 10 CANH 1.433,4.844 1.936,4.992 0.503,0.149 10 13*1 1.433,4.311 1.936,4.460 0.503,0.149 10 12*1 1.391,5.033 1.891,5.182 0.500,0.149 10 E101 1.391,5.033 1.891,5.182 0.500,0.149 10 E101 1.391,4.504 1.891,4.653 0.500,0.149 10 E101 1.892,4.844 2.395,4.992 0.503,0.149 10 7*2 1.892,4.311 2.395,4.460 0.503,0.149 10 6*2 1.85,5.033 2.350,5.182 0.500,0.149 10 E109 1.85,4.504 2.350,4.653 0.500,0.149 10 E109 0.298,5.421 2.753,5.570 2.455,0.149 10 Headlight Leveling ECU Assembly 5.599,7.37 5.960,7.519 0.361,0.149 10 E130 5.599,7.506 7.142,7.854 1.542,0.348 10 Cetification ECU (Smart Key ECU Assembly)*3 5.986,6.991 6.489,7.140 0.503,0.149 10 CANL 5.986,6.447 6.489,6.596 0.503,0.149 10 CANH 5.8,6.361 6.303,6.510 0.503,0.149 10 7 5.8,6.897 6.303,7.046 0.503,0.149 10 8 0.914,7.015 1.417,7.164 0.503,0.149 10 CNL1 0.914,6.469 1.417,6.618 0.503,0.149 10 CNH1 1.384,6.889 1.887,7.038 0.503,0.149 10 9 1.384,6.357 1.887,6.506 0.503,0.149 10 3 0.35,7.394 0.711,7.543 0.361,0.149 10 E161 0.35,7.544 2.458,7.693 2.107,0.149 10 Steering Control ECU*4 2.853,8.24 4.961,8.389 2.107,0.149 10 *3: w/ Entry and Start System 0.205,8.542 2.556,8.691 2.350,0.149 10 *2: w/o Automatic High Beam System 0.205,8.24 2.507,8.389 2.302,0.149 10 *1: w/ Automatic High Beam System 2.853,8.542 5.718,8.692 2.864,0.150 10 *4: w/ Variable Gear Ratio Steering System

C334635E06
3.073,1.094 3.573,1.24 0.5,0.146 10 false 10 3.073,1.625 3.573,1.771 0.5,0.146 10 false 20 5.177,2.031 5.615,2.177 0.438,0.146 10 false E119 5.177,2.198 7.125,2.542 1.948,0.344 10 false Combination Meter Assembly 5.917,1.854 6.417,2 0.5,0.146 10 false CANL 5.917,1.104 6.417,1.25 0.5,0.146 10 false CANH 5.635,1.104 6.135,1.25 0.5,0.146 10 false 39 5.656,1.635 6.156,1.781 0.5,0.146 10 false 40 4.052,1.073 4.552,1.219 0.5,0.146 10 false 7 4.052,1.604 4.552,1.75 0.5,0.146 10 false 17 2.792,2.198 4.875,2.448 2.083,0.25 10 false No. 2 CAN Junction Connector 2.792,2.031 3.229,2.177 0.438,0.146 10 false E133 0.802,1.719 1.302,1.865 0.5,0.146 10 false CANL 0.802,1.177 1.302,1.323 0.5,0.146 10 false CANH 1.417,1.521 1.917,1.667 0.5,0.146 10 false 3*1 1.406,0.99 1.906,1.135 0.5,0.146 10 false 4*1 1.865,1.521 2.365,1.667 0.5,0.146 10 false 2*2 1.854,0.99 2.354,1.135 0.5,0.146 10 false 3*2 2.302,1.521 2.802,1.667 0.5,0.146 10 false 2*3 2.292,0.99 2.792,1.135 0.5,0.146 10 false 3*3 0.323,2.135 1.906,2.5 1.583,0.365 10 false Steering Sensor 1.344,1.198 1.708,1.344 0.365,0.146 10 false E181 1.344,1.729 1.708,1.875 0.365,0.146 10 false E181 1.792,1.198 2.156,1.344 0.365,0.146 10 false E121 1.792,1.729 2.156,1.875 0.365,0.146 10 false E121 2.24,1.198 2.604,1.344 0.365,0.146 10 false E163 2.24,1.729 2.604,1.875 0.365,0.146 10 false E163 0.24,3.219 5.396,3.365 5.156,0.146 10 false *1: w/o Variable Gear Ratio Steering System, w/o Entry and Start System 0.24,3.698 5.396,3.844 5.156,0.146 10 false *2: w/o Variable Gear Ratio Steering System, w/ Entry and Start System 0.24,4.177 3.208,4.323 2.969,0.146 10 false *3: w/ Variable Gear Ratio Steering System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.
U165122E01
0.081,0.049 0.369,0.202 0.288,0.152 10 *a 0.081,1.893 0.369,2.045 0.288,0.152 10 *b 0.25,1.023 0.520,1.162 0.270,0.139 10 A38 0.382,2.621 0.656,2.760 0.274,0.139 10 E22 1.669,2.612 2.35,3.182 2.35,3.182 2.466,3.182 false 2.483,3.104 2.771,3.246 0.288,0.142 10 CG 2.449,0.943 3.132,2.089 3.132,2.089 3.041,2.089 false 1.219,0.306 1.831,0.448 0.612,0.142 10 CANH*A 0.575,0.116 1.793,0.258 1.218,0.142 10 CANL*A, CANH*C 1.904,0.384 2.015,0.384 2.015,0.384 2.362,0.815 false 1.904,1.931 2.015,1.931 2.015,1.931 2.448,1.348 false 0.839,0.47 0.949,0.47 0.949,0.47 2.448,1.227 false 2.025,0.212 2.135,0.212 2.135,0.212 2.448,0.815 false 0.119,0.386 0.704,0.528 0.585,0.142 10 CANH*B 1.192,1.846 1.782,1.988 0.589,0.142 10 CANL*B 2.335,2.005 2.925,2.147 0.589,0.142 10 CANL*C

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1UR-FE, 1GR-FE:
Tester Connection Condition Specified Condition
A38-10 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-11 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher

for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-41 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-49 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-11 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-19 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*A for 1UR-FE, 1GR-FE
*B for 1VD-FTV
*C for 3UR-FE
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3

Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 1VD-FTV) B
OK (for 1GR-FE) C
OK (for 3UR-FE) D
NG E



A

B

C

D

E

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the A38 ECM connector.



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
a.
U165149E02
1.656,2.333 2.406,1.979 2.406,1.979 2.521,1.979 false 0.938,1.073 0.688,1.26 0.688,1.26 0.573,1.26 false 1.021,1.052 0.875,1.583 0.875,1.583 0.74,1.583 false 0.104,0.063 0.417,0.313 0.313,0.25 10 false *a 0.104,1.781 0.396,1.979 0.292,0.198 10 false *b 2.75,0.427 3.24,0.667 0.49,0.24 10 false E119 0.406,2.542 0.802,2.781 0.396,0.24 10 false E22 2.573,1.885 3.021,2.094 0.448,0.208 10 false CG 0.146,1.188 0.76,1.396 0.615,0.208 10 false CANL 0.271,1.5 0.875,1.719 0.604,0.219 10 false CANH

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-39 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E119-40 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the E119 combination meter assembly connector.



NEXT

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)
a.
U165645E02
1.625,3.146 2.531,2.729 2.531,2.729 2.646,2.729 false 1.781,1.5 2.208,2.052 2.208,2.052 2.323,2.052 false 1.646,1.51 1.813,2.313 1.813,2.313 1.948,2.313 false 0.073,0.063 0.479,0.271 0.406,0.208 10 false *a 0.073,2.406 0.417,2.615 0.344,0.208 10 false *b 1.521,0.417 2.021,0.635 0.5,0.219 10 false E145 0.24,3.427 0.625,3.646 0.385,0.219 10 false E22 2.698,2.646 3.083,2.854 0.385,0.208 10 false CG 1.979,2.219 2.51,2.427 0.531,0.208 10 false CA4L 2.375,1.979 2.948,2.198 0.573,0.219 10 false CA4H

Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-18 (CA4H) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-17 (CA4L) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU)
*b Front view of DLC3



OK

NG

6.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the E145 central gateway ECU connector.



NEXT

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

U165501E01
0.09,0.024 0.315,0.194 0.225,0.170 10 *a 4.466,0.024 4.691,0.194 0.225,0.170 10 *b 0.135,0.638 0.704,0.782 0.569,0.144 10 CANH*c 0.142,0.972 0.711,1.116 0.569,0.144 10 CANL*c 0.217,1.128 0.786,1.272 0.569,0.144 10 CANL*d 0.772,1.198 0.965,1.198 0.965,1.198 1.405,1.007 false 0.312,1.286 0.881,1.429 0.569,0.144 10 CANL*e 0.41,1.445 0.979,1.589 0.569,0.144 10 CANL*f 0.392,0.314 0.962,0.458 0.569,0.144 10 CANH*e 0.273,0.472 0.842,0.616 0.569,0.144 10 CANH*d 0.522,0.15 1.091,0.293 0.569,0.144 10 CANH*f 3.257,0.31 3.826,0.454 0.569,0.144 10 CANH*i 0.66,0.009 1.230,0.153 0.569,0.144 10 CANH*g 3.018,0.058 3.588,0.202 0.569,0.144 10 CANH*h 3.255,1.38 3.825,1.523 0.569,0.144 10 CANL*i 3.035,1.614 3.604,1.758 0.569,0.144 10 CANL*h 0.477,1.589 1.046,1.733 0.569,0.144 10 CANL*g 3.509,0.831 3.853,0.973 0.343,0.142 10 E135 2.953,0.819 3.342,0.574 3.342,0.574 3.44,0.574 false 2.588,0.823 2.902,0.11 2.902,0.11 3,0.11 false 1.208,0.819 0.823,0.714 0.823,0.714 0.725,0.714 false 0.87,0.538 1.063,0.538 1.063,0.538 1.433,0.827 false 0.947,0.391 1.189,0.391 1.189,0.391 1.587,0.816 false 1.095,0.215 1.336,0.215 1.336,0.215 1.792,0.811 false 1.235,0.075 1.476,0.075 1.476,0.075 1.974,0.811 false 2.776,0.82 3.019,0.357 3.019,0.357 3.233,0.357 false 2.967,1.001 3.342,1.231 3.342,1.231 3.44,1.231 false 2.588,0.996 2.888,1.66 2.888,1.66 2.986,1.66 false 1.208,0.987 0.795,1.038 0.795,1.038 0.697,1.038 false 0.772,1.198 0.965,1.198 0.965,1.198 1.405,1.007 false 0.848,1.347 1.089,1.347 1.089,1.347 1.587,0.989 false 0.932,1.515 1.173,1.515 1.173,1.515 1.797,1.003 false 1.044,1.655 1.285,1.655 1.285,1.655 1.965,1.003 false 2.776,0.999 3.019,1.448 3.019,1.448 3.233,1.448 false 5.54,0.121 5.809,0.263 0.269,0.142 10 E22 6.624,1.266 7.013,1.410 0.389,0.144 10 CG 5.624,0.761 6.377,1.331 6.377,1.331 6.591,1.331 false 3.479,1.165 4.049,1.308 0.569,0.144 10 CANL*j 3.471,0.52 4.041,0.664 0.569,0.144 10 CANH*j

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3
*c to No. 2 CAN Junction Connector *d to 4WD Control ECU
*e to Power Steering ECU Assembly (w/ Variable Flow Control Solenoid Valve) *f to Airbag Sensor Assembly
*g to Tire Pressure Warning ECU (w/ Tire Pressure Warning System) *h to ECM
*i to Air Conditioning Amplifier Assembly *j to Central Gateway ECU


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E135-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 CAN junction connector
E135-11 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-2 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD control ECU
E135-12 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly*1
E135-13 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-4 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
E135-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-5 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Tire pressure warning ECU*2
E135-15 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-7 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
E135-17 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-8 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
E135-18 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-9 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU
E135-19 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System


Result
Result Proceed to
OK A
NG (ECM CAN main wire) B
NG (Central gateway ECU CAN branch wire) C
NG (No. 2 CAN junction connector CAN main wire) D
NG (ECU or sensor CAN branch wires) E



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ECM)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

D

8.CONNECT CONNECTOR

E

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
8.CONNECT CONNECTOR
a.

Reconnect the E133 No. 1 CAN junction connector.



NEXT

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

U165502E01
0.113,0.045 0.339,0.215 0.225,0.170 10 *a 4.662,0.045 4.887,0.215 0.225,0.170 10 *b 0.292,0.845 0.635,0.987 0.343,0.142 10 E133 0.256,0.519 0.826,0.662 0.569,0.144 10 CANH*c 0.291,1.133 0.861,1.277 0.569,0.144 10 CANL*c 0.478,1.317 1.048,1.460 0.569,0.144 10 CANL*d 1.034,1.386 1.142,1.386 1.142,1.386 1.414,0.999 false 0.629,1.46 1.199,1.604 0.569,0.144 10 CANL*e 0.755,1.606 1.325,1.749 0.569,0.144 10 CANL*f 0.654,0.195 1.223,0.338 0.569,0.144 10 CANH*e 0.394,0.352 0.964,0.496 0.569,0.144 10 CANH*d 0.923,0.03 1.493,0.174 0.569,0.144 10 CANH*f 3.295,0.629 3.864,0.773 0.569,0.144 10 CANH*j 3.15,0.333 3.720,0.477 0.569,0.144 10 CANH*h 3.006,0.165 3.575,0.309 0.569,0.144 10 CANH*g 3.226,0.457 3.796,0.601 0.569,0.144 10 CANH*i 3.341,1.084 3.911,1.227 0.569,0.144 10 CANL*j 3.097,1.364 3.666,1.508 0.569,0.144 10 CANL*h 2.78,0.853 3.118,0.525 3.118,0.525 3.217,0.525 false 2.401,0.858 2.866,0.229 2.866,0.229 2.964,0.229 false 0.992,0.418 1.058,0.418 1.058,0.418 1.414,0.847 false 1.209,0.271 1.311,0.271 1.311,0.271 1.594,0.836 false 1.496,0.096 1.626,0.096 1.626,0.096 1.813,0.831 false 2.589,0.855 2.93,0.399 2.93,0.399 3.144,0.399 false 2.794,1.021 3.052,1.279 3.052,1.279 3.15,1.279 false 2.401,1.017 2.912,1.582 2.912,1.582 3.01,1.582 false 3.109,0.839 3.171,0.683 3.171,0.683 3.269,0.683 false 3.095,1.007 3.201,1.15 3.201,1.15 3.299,1.15 false 1.19,0.839 0.945,0.595 0.945,0.595 0.846,0.595 false 1.19,1.007 0.945,1.198 0.945,1.198 0.846,1.198 false 1.034,1.386 1.142,1.386 1.142,1.386 1.414,0.999 false 1.179,1.535 1.253,1.535 1.253,1.535 1.594,1.01 false 1.277,1.675 1.351,1.675 1.351,1.675 1.79,1.024 false 3.175,1.207 3.744,1.351 0.569,0.144 10 CANL*i 2.589,1.02 2.994,1.427 2.994,1.427 3.067,1.427 false 5.52,0.165 5.792,0.313 0.272,0.148 10 E22 6.617,1.287 6.969,1.430 0.352,0.144 10 CG 5.629,0.786 6.37,1.352 6.37,1.352 6.584,1.352 false 3.036,1.523 3.605,1.666 0.569,0.144 10 CANL*g

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3
*c to No. 1 CAN Junction Connector *d to Main Body ECU (Multiplex Network Body ECU)
*e to Master Cylinder Solenoid (Skid Control ECU) *f to Headlight Leveling ECU Assembly
*g to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *h to Combination Meter Assembly
*i to Steering Control ECU (w/ Variable Gear Ratio Steering System) *j to Steering Sensor


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E133-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector
E133-11 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-2 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
E133-12 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Master cylinder solenoid (skid control ECU)
E133-13 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-4 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight leveling ECU assembly
E133-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*1
E133-16 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-7 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
E133-17 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-8 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering control ECU*2
E133-18 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-10 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor
E133-20 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: w/ Entry and Start System

*2: w/ Variable Gear Ratio Steering System


Result
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

D

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
U165617E02
1.635,3.073 2.51,2.667 2.51,2.667 2.625,2.667 false 1.75,1.125 2.281,1.677 2.281,1.677 2.396,1.677 false 1.677,1.135 1.885,1.958 1.885,1.958 2.021,1.958 false 0.052,0.063 0.365,0.24 0.313,0.177 10 false *a 0.052,2.281 0.427,2.521 0.375,0.24 10 false *b 1.531,0.292 1.99,0.479 0.458,0.188 10 false E145 0.219,3.24 0.615,3.427 0.396,0.188 10 false E22 2.667,2.573 3.073,2.792 0.406,0.219 10 false CG 2.448,1.583 3,1.792 0.552,0.208 10 false CA4L 2.063,1.875 2.615,2.052 0.552,0.177 10 false CA4H

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-18 (CA4H) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-17 (CA4L) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Component with harness connected
(Central Gateway ECU)
*b Front view of DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR