Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Open in Bus 2 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 2 main lines and/or a central gateway ECU CAN branch wire when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU is 70 Ω or higher

Detection Item Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of central gateway ECU is 70 Ω or higher.
·

Bus 2 CAN main wire or connector

·

Bus 2 CAN branch wire or connector

·

ECM

·

Combination meter assembly

·

Central gateway ECU

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector



This malfunction is not related to the lines of a bus 2 branch except the central gateway ECU CAN branch wires or to ECUs or sensors connected a bus 2 branch.

WIRING DIAGRAM

C329403E07
6.219,1.823 6.677,2.01 0.458,0.188 10 false ECM 6.219,1.667 6.573,1.844 0.354,0.177 10 false A52 6.104,0.74 6.719,0.938 0.615,0.198 10 false CANH 6.104,1.385 6.719,1.583 0.615,0.198 10 false CANL 5.229,0.688 6.031,0.927 0.802,0.24 10 false 10*1, 41*2 5.219,1.177 6.063,1.354 0.844,0.177 10 false 11*1, 49*2 3.063,0.719 3.375,0.917 0.313,0.198 10 false 7 3.063,1.198 3.375,1.396 0.313,0.198 10 false 17 2.104,0.729 2.417,0.927 0.313,0.198 10 false 8 2.031,1.188 2.344,1.385 0.313,0.198 10 false 18 3.063,3.156 3.375,3.354 0.313,0.198 10 false 1 3.031,3.625 3.344,3.823 0.313,0.198 10 false 11 4,3.156 4.313,3.354 0.313,0.198 10 false 1 3.958,3.615 4.333,3.844 0.375,0.229 10 false 11 4.938,3.135 5.25,3.333 0.313,0.198 10 false 7 4.938,3.604 5.25,3.802 0.313,0.198 10 false 17 0.75,0.792 1.365,0.99 0.615,0.198 10 false CA4H 0.771,1.281 1.385,1.479 0.615,0.198 10 false CA4L 1.26,0.729 1.573,0.927 0.313,0.198 10 false 18 1.281,1.177 1.594,1.375 0.313,0.198 10 false 17 0.313,1.792 2.24,2.073 1.927,0.281 10 false Central Gateway ECU 0.333,1.615 0.948,1.885 0.615,0.271 10 false E145 1.604,4.271 3.583,4.74 1.979,0.469 10 false No. 1 CAN Junction Connector 3.667,4.271 5.635,4.688 1.969,0.417 10 false No. 2 CAN Junction Connector 5.76,4.271 7.052,4.906 1.292,0.635 10 false Combination Meter Assembly 1.604,4.115 2.063,4.313 0.458,0.198 10 false E133 3.667,4.094 4.125,4.292 0.458,0.198 10 false E135 5.771,4.115 6.25,4.375 0.479,0.26 10 false E119 6.104,3.135 6.719,3.333 0.615,0.198 10 false CANH 6.115,3.833 6.729,4.031 0.615,0.198 10 false CANL 5.781,3.135 6.052,3.333 0.271,0.198 10 false 39 5.792,3.604 6.063,3.792 0.271,0.188 10 false 40 0.135,5.188 2,5.5 1.865,0.313 10 false *2: for 1VD-FTV 0.135,4.875 2.198,5.125 2.063,0.25 10 false *1: for 1UR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.
U166171E02
2.396,1.188 2.531,0.385 2.531,0.385 2.615,0.385 false 2.031,0.406 2.115,0.406 2.115,0.406 2.313,0.792 false 2.031,1.823 2.115,1.823 2.115,1.823 2.396,1.302 false 2.188,0.177 2.271,0.177 2.271,0.177 2.396,0.792 false 0.333,1 0.76,1.219 0.427,0.219 10 false A52 0.083,0.073 0.427,0.344 0.344,0.271 10 false *a 1.323,0.333 2.021,0.531 0.698,0.198 10 false CANH*A 1.521,0.104 2.229,0.302 0.708,0.198 10 false CANL*A 2.646,0.302 3.365,0.521 0.719,0.219 10 false CANH*B 1.365,1.74 2.104,1.948 0.74,0.208 10 false CANL*B

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1UR-FE:
Tester Connection Condition Specified Condition
A52-10 (CANH) - A52-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1VD-FTV:
Tester Connection Condition Specified Condition
A52-41 (CANH) - A52-49 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*A for 1UR-FE
*B for 1VD-FTV
*a Front view of wire harness connector
(to ECM)

Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 1VD-FTV) B
NG C



A

B

C

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the A52 ECM connector.



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
a.
U165131E01
1.539,0.276 1.951,0.414 0.412,0.137 10 E119 0.252,1.752 0.671,1.889 0.419,0.137 10 CANH 0.14,1.372 0.550,1.510 0.409,0.137 10 CANL 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 0.978,1.264 0.752,1.454 0.752,1.454 0.624,1.454 false 1.061,1.264 0.939,1.845 0.939,1.845 0.76,1.845 false

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-39 (CANH) - E119-40 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the E119 combination meter assembly connector.



NEXT

5.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)
a.
U165594E01
0.071,0.041 0.241,0.194 0.170,0.153 10 *a 1.505,0.138 1.852,0.277 0.347,0.139 10 E145 2.384,1.67 3.026,1.821 0.642,0.151 10 CA4H 2.032,1.888 2.674,2.039 0.642,0.151 10 CA4L 1.78,1.197 2.245,1.773 2.245,1.773 2.359,1.773 false 2.014,1.971 1.825,1.971 1.825,1.971 1.646,1.197 false

Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-18 (CA4H) - E145-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU)



OK

NG

6.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the E145 central gateway ECU connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

U165466E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 3.433,0.199 3.776,0.341 0.343,0.142 10 E133 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.711,1.2 2.280,1.344 0.569,0.144 10 CANL*b 4.179,1.027 4.743,1.271 4.743,1.271 4.841,1.271 false 3.993,1.022 4.464,1.588 4.464,1.588 4.562,1.588 false 2.609,1.026 2.364,1.271 2.364,1.271 2.266,1.271 false 4.168,0.851 4.743,0.595 4.743,0.595 4.841,0.595 false 3.993,0.844 4.464,0.278 4.464,0.278 4.562,0.278 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 4.593,0.214 5.163,0.358 0.569,0.144 10 CANH*c 4.863,0.536 5.433,0.680 0.569,0.144 10 CANH*d 4.86,1.197 5.429,1.340 0.569,0.144 10 CANL*d 4.586,1.522 5.156,1.666 0.569,0.144 10 CANL*c

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to ECM *d to Central Gateway ECU


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E133-1 (CANH) - E133-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
E133-7 (CANH) - E133-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
E133-8 (CANH) - E133-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU


Result
Result Proceed to
OK A
NG (ECM CAN main wire) B
NG (Central gateway ECU CAN branch wire) C
NG (No. 2 CAN junction connector CAN main wire) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ECM)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

D

8.CONNECT CONNECTOR
8.CONNECT CONNECTOR
a.

Reconnect the E133 No. 1 CAN junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

U165467E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 3.433,0.199 3.776,0.341 0.343,0.142 10 E135 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.711,1.2 2.280,1.344 0.569,0.144 10 CANL*b 3.993,1.022 4.464,1.438 4.464,1.438 4.562,1.438 false 2.609,1.026 2.364,1.271 2.364,1.271 2.266,1.271 false 3.993,0.844 4.524,0.338 4.524,0.338 4.622,0.338 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 4.653,0.274 5.223,0.417 0.569,0.144 10 CANH*c 4.586,1.373 5.156,1.517 0.569,0.144 10 CANL*c

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to Combination Meter Assembly - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E135-1 (CANH) - E135-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector
E135-7 (CANH) - E135-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly


Result
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)