Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255549 POWER DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  B1243  GSW Terminal Circuit Malfunction  


DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU is detected, DTC B1243 is stored.

HINT:

If DTC B1243 is stored, the speed-sensitive automatic door lock function, shift-linked automatic door lock function, and collision door lock release function are prohibited.


DTC Code DTC Detection Condition Trouble Area
B1243 When either of the following occurs:
·

An open or short in the GSW input circuit of the main body ECU.

·

The collision door lock release function does not operate normally.


·

Harness or connector

·

Airbag sensor assembly

·

Main body ECU



WIRING DIAGRAM

B298696E03
5.5,0.583 5.865,0.74 0.365,0.156 10 false GSW 1.229,0.594 1.594,0.75 0.365,0.156 10 false GSW 5.198,1.833 5.448,1.99 0.25,0.156 10 false A 5.177,2 6.823,2.406 1.646,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 4.156,1.292 5.365,1.646 1.208,0.354 10 false Cowl Side Junction Block LH 5.26,0.521 5.448,0.677 0.188,0.156 10 false 24 4.167,1.104 4.354,1.281 0.188,0.177 10 false 5A 0.563,1.313 1.938,1.688 1.375,0.375 10 false Center Airbag Sensor Assembly 0.594,1.115 0.875,1.292 0.281,0.177 10 false N52 3.938,0.5 4.125,0.656 0.188,0.156 10 false 60 1.656,0.49 1.844,0.646 0.188,0.156 10 false 18

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

As the door control battery is installed between the vehicle battery and main body ECU, first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION).



PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK MAIN BODY ECU (GSW VOLTAGE)
2.CHECK MAIN BODY ECU (GSW VOLTAGE)
a.
U156270E01
0.455,0.962 0.752,1.133 0.297,0.171 10 E47 0.499,1.67 0.865,1.841 0.366,0.171 10 GSW 0.073,0.038 0.254,0.209 0.181,0.171 10 *a 1.443,1.08 1.127,1.752 1.127,1.752 0.94,1.752 false

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

Turning the ignition switch to ON with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Disconnect the airbag sensor assembly connector (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


c.

Connect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E47-18 (GSW) - Body ground Ignition switch ON 2.8 to 4.3V


Text in Illustration
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - AIRBAG SENSOR ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

Turning the ignition switch to ON with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Disconnect the 2I cowl side junction block LH connector.


c.

Disconnect the E47 airbag sensor assembly connector (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2I-7 - E47-18 (GSW) Always Below 1 Ω
2I-7 or E47-18 (GSW) - Body ground Always 10 kΩ or higher




OK

4.INSPECT COWL SIDE JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT COWL SIDE JUNCTION BLOCK LH

b.

Remove the main body ECU from the cowl side junction block LH.


c.

Measure the resistance according to the value(s) in the table below.

U155927E04
3,1.656 3.25,2.26 3.25,2.26 3.771,2.26 true 2.104,0.771 2.531,0.979 0.427,0.208 10 false A 5.667,0.781 6.094,0.99 0.427,0.208 10 false 2I 3.865,2.177 4.292,2.385 0.427,0.208 10 false GSW 0.115,0.021 0.542,0.229 0.427,0.208 10 false *a

Text in Illustration
*a Component without harness connected
(Cowl Side Junction Block LH)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
A-24(GSW) - 2I-7 Always Below 1 Ω


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

B

C

REPLACE COWL SIDE JUNCTION BLOCK LH (for LHD)

D

REPLACE COWL SIDE JUNCTION BLOCK LH (for RHD)