Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255549 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Power Source Circuit  


DESCRIPTION

The main power source for the main body ECU (cowl side junction block LH) is supplied via the door control battery.

WIRING DIAGRAM

E329053E05
0.083,0.573 1.083,0.958 1,0.385 10 false from Battery 1.458,0.729 2.458,1.115 1,0.385 10 false MPX-B NO.1 1.594,1.24 2.323,1.625 0.729,0.385 10 false D/L NO.1 2.708,1.281 3.167,1.51 0.458,0.229 10 false BECU 2.365,1.073 3.094,1.458 0.729,0.385 10 false BATB 2.219,1 2.49,1.229 0.271,0.229 10 false 5 2.365,1.698 2.896,1.938 0.531,0.24 10 false GND1 2.198,1.583 2.448,1.823 0.25,0.24 10 false 2 2.365,2.354 2.865,2.563 0.5,0.208 10 false GND2 2.156,2.219 2.385,2.448 0.229,0.229 10 false 10 3.167,1.167 3.427,1.396 0.26,0.229 10 false 4 2.698,2.063 3.333,2.344 0.635,0.281 10 false EDOR 3.156,1.969 3.385,2.177 0.229,0.208 10 false 3 3.792,0.583 4.125,0.813 0.333,0.229 10 false 2H 3.792,0.365 4.521,0.75 0.729,0.385 10 false 19 3.792,1.271 4.073,1.458 0.281,0.188 10 false 2J 3.792,1.063 4.052,1.26 0.26,0.198 10 false 10 3.792,2.063 4.021,2.271 0.229,0.208 10 false 2J 3.781,1.833 3.979,2.031 0.198,0.198 10 false 23 5.396,1.938 5.677,2.177 0.281,0.24 10 false 31 2.146,2.979 2.875,3.365 0.729,0.385 10 false E168 2.146,3.146 3.563,3.531 1.417,0.385 10 false Door Control Battery 4.365,2.427 5.635,2.875 1.271,0.448 10 false Cowl Side Junction Block LH 5.646,3.083 5.896,3.333 0.25,0.25 10 false A 5.646,3.292 6.854,3.563 1.208,0.271 10 false Main Body ECU 5.646,2.042 6.198,2.271 0.552,0.229 10 false BECU

CAUTION / NOTICE / HINT

NOTICE:
·

As the door control battery is installed between the vehicle battery and main body ECU, first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - BATTERY AND BODY GROUND)
a.
U164356E02
1.448,1.042 1.208,0.344 1.208,0.344 0.875,0.344 false 1.802,1.031 1.854,0.146 1.854,0.146 2.188,0.146 false 1.969,1.031 2.156,0.563 2.156,0.563 2.5,0.563 true 1.802,1.365 1.625,1.823 1.625,1.823 1.292,1.823 true 0.427,1.021 0.833,1.208 0.406,0.188 10 false E168 0.49,0.271 0.906,0.458 0.417,0.188 10 false GND1 2.24,0.063 2.656,0.25 0.417,0.188 10 false BECU 0.052,0 0.271,0.188 0.219,0.188 10 false *a 2.563,0.469 2.979,0.656 0.417,0.188 10 false BECU 0.896,1.75 1.313,1.938 0.417,0.188 10 false GND1

Disconnect the door control battery connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E168-2 (GND1) - Body ground Always Below 1 Ω
E168-10 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E168-4 (BECU) - Body ground Always 11 to 14 V
E168-5 (BATB) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Door Control Battery)


OK

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - COWL SIDE JUNCTION BLOCK LH)

NG

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - COWL SIDE JUNCTION BLOCK LH)
a.

Disconnect theE168 door control battery connector.


b.

Disconnect the 2J cowl side junction block LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E168-3 (EDOR) - 2J-23 Always Below 1 Ω
E168-3 (EDOR) or 2J-23 - Body ground Always 10. kΩ or higher




OK

3.INSPECT COWL SIDE JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COWL SIDE JUNCTION BLOCK LH
a.

Remove the cowl side junction block LH.



U166547E02
3.208,2.208 3.521,2.208 3.521,2.208 3.771,1.656 true 0.073,0 0.438,0.24 0.365,0.24 10 false *a 2.021,0.927 2.385,1.167 0.365,0.24 10 false A 5.646,0.771 6.01,1.01 0.365,0.24 10 false 2J 2.813,2.135 3.521,2.375 0.708,0.24 10 false BECU

Text in Illustration
*a Component without harness connected
(Cowl Side Junction Block LH)
- -

b.

Remove the main body ECU from the cowl side junction block LH.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A-31 (EDOR) - 2J-23 Always Below 1 Ω


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

4.CHECK DOOR CONTROL BATTERY (POWER OUTPUT)

B

REPLACE COWL SIDE JUNCTION BLOCK LH (for LHD)

C

REPLACE COWL SIDE JUNCTION BLOCK LH (for RHD)

4.CHECK DOOR CONTROL BATTERY (POWER OUTPUT)
a.

Turn the ignition switch off.


b.

Remove the MPX-B NO. 1 fuse from the engine room relay block. and leave the vehicle as is for 50 minutes.


c.

Leave the vehicle as is for 30 minutes (wait until the door control battery is discharged).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E168-3 (EDOR) - Body ground Ignition switch off Below 2 V



e.

Install the MPX-B NO.1 fuse to the engine room relay block.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E168-3 (EDOR) - Body ground Ignition switch off 11 to 14 V



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

REPLACE COWL SIDE JUNCTION BLOCK LH (for LHD)

B

REPLACE COWL SIDE JUNCTION BLOCK LH (for RHD)

C