Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255553 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is ACC or off and the key is in the ignition key cylinder. The key reminder warning buzzer is activated when the main body ECU sends an unlock warning switch signal and front door courtesy light switch LH*1 or RH*2 signal to the combination meter.

*1: for LHD

*2: for RHD


WIRING DIAGRAM

B205678E04
3.969,1.99 5.677,2.177 1.708,0.188 10 false CAN Communication Line 6.208,2.125 6.688,2.292 0.479,0.167 10 false Buzzer 2.885,2.375 3.083,2.542 0.198,0.167 10 false E1 2.885,1.271 3.083,1.438 0.198,0.167 10 false E4 0.813,1.167 0.927,1.344 0.115,0.177 10 false 2 2.375,1.167 2.49,1.344 0.115,0.177 10 false 1 2.01,1.167 2.323,1.344 0.313,0.177 10 false UN+ 0.99,1.167 1.302,1.344 0.313,0.177 10 false UN- 2.375,2.26 2.49,2.438 0.115,0.177 10 false 1 0.792,2.719 1.625,2.896 0.833,0.177 10 false K2*1, L1*2 0.052,3.271 0.885,3.448 0.833,0.177 10 false *1: for LHD 0.052,3.531 0.885,3.708 0.833,0.177 10 false *2: for RHD 0.792,2.885 2.729,3.25 1.938,0.365 10 false Front Door Courtesy Light Switch Assembly LH*1, RH*2 0.792,1.615 1.073,1.792 0.281,0.177 10 false E94 0.792,1.771 2.896,2.115 2.104,0.344 10 false Unlock Warning Switch Assembly 2.875,2.74 4.531,3.115 1.656,0.375 10 false Main Body ECU (Cowl Side Junction Block LH) 5.615,2.781 6.927,3.167 1.313,0.385 10 false Combination Meter Assembly 3.198,2.365 3.615,2.552 0.417,0.188 10 false DCTY 3.198,1.25 3.615,1.438 0.417,0.188 10 false KSW 2.896,2.198 3.083,2.354 0.188,0.156 10 false 24 2.927,1.094 3.042,1.25 0.115,0.156 10 false 5

CAUTION / NOTICE / HINT

HINT:

Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting CAN communication in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH)
a.

Check the Data List for proper functioning of the front door courtesy light switch (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy SW Driver side door courtesy light switch signal / ON or OFF ON: Driver side door opened
OFF: Driver side door closed
-



OK

2.READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH)
a.

Check the Data List for proper functioning of the unlock warning switch (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal / ON or OFF ON: Key in ignition key cylinder
OFF: No key in ignition key cylinder
-

OK:

On tester screen, item changes between ON and OFF according to above chart.




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.
E198930E02
2.567,1.406 2.875,1.562 0.309,0.156 10 UN+ 0.633,1.393 0.942,1.549 0.309,0.156 10 UN- 1.948,1.33 2.524,1.476 false 1.62,1.333 0.974,1.476 false

Remove the unlock warning switch (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (UN+) - 2 (UN-) Not pushed 10 kΩ or higher
Pushed Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the E94 unlock warning switch connector.


b.

Disconnect the E4 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E94-1 (UN+) - E4-5 (KSW) Always Below 1 Ω
E94-2 (UN-) - Body ground Always Below 1 Ω
E94-1 (UN+) - Body ground Always 10 kΩ or higher




OK

5.CHECK COMBINATION METER ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK COMBINATION METER ASSEMBLY (OPERATION)
a.

Temporarily replace the combination meter assembly with a new or normally functioning one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL).


b.

Check the key reminder warning system (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK).

OK:

The key reminder warning system functions properly.




OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)