Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The main body ECU and the combination meter are connected with a cable and the CAN communication line. DTC B2282 is stored when signals, transmitted through the cable and communication line, do not match.

DTC Code Detection Condition Trouble Area
B2282 When the following conditions are met:
·

Signals between the main body ECU and combination meter are inconsistent.


·

A malfunction is detected in the circuit between the vehicle speed sensor and combination meter.


·

Main body ECU


·

Combination meter assembly


·

Harness or connector



The skid control ECU converts signals from the speed sensor into 4-pulse signals and sends them to the combination meter. After these signals are converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, they are then transmitted to the main body ECU. The main body ECU determines the vehicle speed based on the frequencies of these pulse signals.

DTC Code Detection Condition Trouble Area
B2283 When both of the conditions below are met:
·

Vehicle speed decreases significantly.


·

Vehicle speed does not correspond with engine speed.


·

Main body ECU


·

Combination meter assembly


·

Speed sensor


·

Skid control ECU


·

Harness or connector



C166257E04
2.923,1.334 4.143,1.718 1.220,0.384 10 Combination Meter 0.43,4.416 2.179,4.600 1.749,0.185 10 : CAN Communication Line 4.944,2.563 6.388,2.748 1.444,0.185 10 B2282 Detection Area 2.972,3.623 4.416,3.808 1.444,0.185 10 B2283 Detection Area 0.576,3.025 1.586,3.209 1.010,0.185 10 Speed Sensor 0.498,1.423 1.653,1.608 1.156,0.185 10 Skid Control ECU 2.036,1.081 2.624,1.266 0.589,0.185 10 4 Pulses 4.558,1.081 5.146,1.266 0.589,0.185 10 4 Pulses 5.436,1.034 6.775,1.553 1.339,0.520 10 Main Body ECU (Cowl Side Junction Block LH)

WIRING DIAGRAM

C357852E01
1.542,1.333 2.156,1.531 0.615,0.198 10 false CANH 1.552,1.792 2.167,1.99 0.615,0.198 10 false CANL 1.74,2.25 2.354,2.448 0.615,0.198 10 false +S 2.083,1.458 2.698,1.656 0.615,0.198 10 false 25 2.083,1.917 2.698,2.115 0.615,0.198 10 false 26 2.104,2.385 2.719,2.583 0.615,0.198 10 false 4 3.271,1.5 4.083,1.698 0.813,0.198 10 false CAN Line 3.26,1.969 4.073,2.167 0.813,0.198 10 false CAN Line 4.938,1.469 5.552,1.667 0.615,0.198 10 false 5 4.938,1.938 5.552,2.135 0.615,0.198 10 false 6 4.948,2.354 5.563,2.552 0.615,0.198 10 false 9 5.167,1.344 5.979,1.542 0.813,0.198 10 false CANH 5.188,1.813 6,2.01 0.813,0.198 10 false CANL 5.208,2.25 6.021,2.448 0.813,0.198 10 false SPD 0.792,2.865 1.406,3.063 0.615,0.198 10 false E7 0.792,3.01 2.094,3.208 1.302,0.198 10 false Combination Meter 5.042,2.854 5.656,3.052 0.615,0.198 10 false E3 5.042,3.021 6.563,3.438 1.521,0.417 10 false Main Body ECU (Cowl Side Junction Block LH)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED SIGNAL)
a.

Use the Data List to check if the vehicle speed signal is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle speed signal/STOP or RUN STOP: Vehicle stopped
RUN: Vehicle running
-

Result
Result Proceed to
Display on the intelligent tester does not change according to vehicle condition A
Display on the intelligent tester changes according to vehicle condition B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COMBINATION METER)

B

REPLACE MAIN BODY ECU

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COMBINATION METER)
U163027E01
1.615,0.89 1.990,1.123 0.375,0.233 10 E3 5.033,0.896 5.408,1.129 0.375,0.233 10 E7 0.508,0.158 2.917,0.525 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 2.502,2.13 2.856,2.332 0.354,0.202 10 SPD 3.731,1.211 3.987,1.413 0.257,0.202 10 +S 3.924,0.158 6.332,0.525 2.408,0.367 10 Front view of wire harness connector: (to Combination Meter) 3.981,1.278 4.072,1.278 4.072,1.278 4.693,1.748 false 2.46,2.225 2.373,2.225 2.373,2.225 1.867,1.912 false

a.

Disconnect the E3 main body ECU connector.


b.

Disconnect the E7 combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-9 (SPD) - E7-4 (+S) Always Below 1 Ω
E3-9 (SPD) or E7-4 (+S) - Body ground Always 10 kΩ or higher




OK

3.REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE MAIN BODY ECU
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check whether DTC B2282 and B2283 are output.

Result
Result Proceed to
DTC not output A
DTC output (w/ Multi-information Display) B
DTC output (w/o Multi-information Display) C



A

END

B

C