Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2284 The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

STOP fuse

·

SFI system

·

ECD system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Connect the cable to the negative (-) battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more.

*: Only detected while a malfunction is present and the engine switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the indicator in the combination meter is not illuminated in green). However, the engine can be started by turning the engine switch on (ACC) and then pressing and holding it.
·

If there is a malfunction when the direct line is on, the engine can be started by pressing the engine switch with the brake pedal released.

·

If there is a malfunction when the direct line is off, the engine cannot be started by pressing the engine switch with the brake pedal depressed.


-

Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2284
Power Source Control
·

Stop Light Switch1


-

WIRING DIAGRAM

C339123E04
0.313,0.635 1.333,0.885 1.021,0.25 10 false from Battery 2.365,0.802 3.094,1.031 0.729,0.229 10 false AM2 3.854,0.656 4.292,0.813 0.438,0.156 10 false E130 4.24,0.646 4.677,0.802 0.438,0.156 10 false +B 3.917,0.458 4.354,0.615 0.438,0.156 10 false 10 3.844,2.333 4.281,2.49 0.438,0.156 10 false E128 1.656,2.49 2.125,2.677 0.469,0.188 10 false STOP 2.302,2.229 2.49,2.385 0.188,0.156 10 false 1 2.302,2.531 2.49,2.688 0.188,0.156 10 false 3 2.469,2.333 2.813,2.49 0.344,0.156 10 false B 3.281,2.25 3.625,2.406 0.344,0.156 10 false L 2.469,2.625 2.813,2.781 0.344,0.156 10 false GND 2.323,2.969 2.667,3.125 0.344,0.156 10 false A73 2.313,3.125 3.427,3.531 1.115,0.406 10 false Stop Light Switch Assembly 4.229,2.24 4.667,2.396 0.438,0.156 10 false STP1 4.906,2.448 5.344,2.604 0.438,0.156 10 false IC 2.844,2.417 3.281,2.573 0.438,0.156 10 false IC 3.958,2.125 4.396,2.281 0.438,0.156 10 false 2 3.427,2.25 3.865,2.406 0.438,0.156 10 false 2 3.854,3.198 4.292,3.354 0.438,0.156 10 false E130 4.25,3.188 4.688,3.344 0.438,0.156 10 false E 3.938,3 4.375,3.156 0.438,0.156 10 false 11 0.302,2.333 1.208,2.604 0.906,0.271 10 false from Battery 0.74,4.135 3.24,4.292 2.5,0.156 10 false : CAN Communication Line 0.51,1.438 1.292,1.615 0.781,0.177 10 false to ECUs 4,3.781 5.604,4.167 1.604,0.385 10 false Certification ECU (Smart Key ECU Assembly) 6.323,2.917 6.708,3.094 0.385,0.177 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Check the connector connection to the terminal to make sure that there is no abnormality such as a loose connection, deformation, etc.


NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly) or ECM, refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH 1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Specified Condition
Stop Light Switch1 State of brake pedal/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.



OK:

The GTS display changes correctly in response to the brake pedal operation.


Result
Result Proceed to
OK A
NG for SFI system B
for ECD system C

HINT:

·

For the ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING), refer to the following:






A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the E128 certification ECU (smart Key ECU assembly) connector.


b.

Disconnect the A73 connector from the stop light switch assembly.


c.
U165454E01
0.156,0.114 0.342,0.273 0.186,0.158 10 *a 0.804,1.694 1.016,1.853 0.212,0.158 10 B 1.298,1.297 1.121,1.762 1.121,1.762 0.986,1.762 false 1.602,0.148 2.015,0.306 0.413,0.158 10 A73

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A73-1 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
E128-2 (STP1) - A73-2 (L) Always Below 1 Ω
A73-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the E128 and E130 certification ECU (smart Key ECU assembly) connectors.


b.

Reconnect the A73 connectors from the stop light switch assembly.


c.
U165442E01
0.078,0.031 0.266,0.189 0.189,0.158 10 *a 2.443,1.707 2.939,1.865 0.497,0.158 10 STP1 2.162,0.868 2.243,1.765 2.243,1.765 2.383,1.765 false 1.481,0.126 1.894,0.284 0.413,0.158 10 E128

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E128-2 (STP1) - Body ground Brake pedal released → depressed 1 V or less → 9 V or higher


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY