Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Theft Warning Siren Circuit  


DESCRIPTION

The theft warning siren has an internal battery. If the vehicle battery cable is disconnected or any of the communication lines are open, the theft warning siren detects this and sounds its siren.

Although the theft warning siren usually sounds by receiving a signal from the main body ECU (multiplex network body ECU), the theft warning siren can sound by its internal battery in case the vehicle battery cable is disconnected.

The main body ECU (multiplex network body ECU) sends an arming signal to the theft warning siren while transferring to the armed state, and it also sends a disarming signal to the siren while switching to the disarmed state. Also, the main body ECU (multiplex network body ECU) can cause the theft warning siren to sound by sending an alarm signal during the alarm sounding state.

WIRING DIAGRAM

B312497E23
1.719,0.281 2.677,0.531 0.958,0.25 10 false from Battery 3.646,0.438 4.354,0.635 0.708,0.198 10 false S-HORN 1.188,1.604 1.344,1.802 0.156,0.198 10 false 3 1.396,1.771 1.844,1.99 0.448,0.219 10 false GND 1.333,2.688 1.781,2.906 0.448,0.219 10 false E169 1.344,2.865 4.021,3.24 2.677,0.375 10 false Theft Warning Siren Assembly 3.417,1.75 3.948,1.969 0.531,0.219 10 false CONT 3.594,1.219 3.885,1.438 0.292,0.219 10 false +B 3.906,1.146 4.063,1.344 0.156,0.198 10 false 1 3.906,1.635 4.063,1.833 0.156,0.198 10 false 2 5.354,1.625 5.573,1.833 0.219,0.208 10 false 18 5.635,1.76 6.25,1.958 0.615,0.198 10 false SSCL 5.583,2.927 6.198,3.125 0.615,0.198 10 false E117 5.604,3.094 6.865,3.729 1.26,0.635 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the theft warning siren assembly is replaced, refer to the Service Bulletin.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION).



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SEQURITY HORN2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Horn2 Theft warning siren OFF/ON -


OK:

The theft warning siren assembly sounds and stops correctly when operated through the GTS.

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - BATTERY AND BODY GROUND)
a.
U164372E01
1.422,0.149 1.928,0.385 0.506,0.236 10 E169 0.333,1.581 0.594,1.747 0.261,0.165 10 +B 2.845,0.055 3.218,0.220 0.372,0.165 10 GND 0.635,1.665 0.727,1.665 0.727,1.665 1.324,1.174 false 2.797,0.132 2.67,0.132 2.67,0.132 1.986,1.093 false

Disconnect the E169theft warning siren assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E169-1 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E169-3 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Theft Warning Siren Assembly)


OK

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the E169 theft warning siren assembly connector.


b.

Disconnect the E117 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E169-2 (CONT) - E117-18 (SSCL) Always Below 1 Ω
E169-2 (CONT) - Body ground Always 10 kΩ or higher
E117-18 (SSCL) - Body ground Always 10 kΩ or higher




OK

4.CHECK THEFT WARNING SIREN ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK THEFT WARNING SIREN ASSEMBLY
a.

Temporarily replace the theft warning siren assembly with a new or normally functioning one.

HINT:

Refer to Service Bulletin.



b.

Check the operation of the theft warning siren assembly function.

OK:

Theft warning siren assembly function operates normally.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (THEFT WARNING SIREN ASSEMBLY WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)