Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Intrusion Sensor Circuit  


DESCRIPTION

If no warnings operate or the system can be set even though the conditions to set the system are not met, the main body ECU (multiplex network body ECU) cannot perform recognition due to a cutoff of the ON signal from the courtesy light switch from the doors, engine hood or luggage compartment door, or some other problem.

If the automatic alarm operates when it should not operate, it may be due to a false detection by the intrusion sensor (theft warning ultrasonic sensor) or due to the ON signal being input when there is a short circuit in the courtesy light switch of the doors, engine hood or luggage compartment door, or some other problem which would cause this to happen.


HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic sensor) may operate and cause the automatic alarm system to operate even when the sensor is normal.

·

The driver steps away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

A window or the sliding roof is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car washing machine.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



WIRING DIAGRAM

B373997E09
1.615,2.677 2.917,2.906 1.302,0.229 10 false Map Light Assembly 1.094,0.406 2.052,0.604 0.958,0.198 10 false from Battery 5,2.604 7.156,3 2.156,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 1.521,1.271 3.448,1.792 1.927,0.521 10 false Intrusion Sensor (Theft Warning Ultrasonic Sensor) 1.604,2.479 2.375,2.677 0.771,0.198 10 false R7 0.917,1.552 1.646,1.74 0.729,0.188 10 false GND9 0.667,1.552 1.396,1.74 0.729,0.188 10 false 17 3.74,1.25 4.469,1.438 0.729,0.188 10 false +B2 3.719,1.823 4.448,2.01 0.729,0.188 10 false IOUT 4.083,1.24 4.813,1.427 0.729,0.188 10 false 15 4.115,1.802 4.844,1.99 0.729,0.188 10 false 12 5.396,1.813 6.125,2 0.729,0.188 10 false 12 5.625,1.875 6.354,2.063 0.729,0.188 10 false ISIF 5.01,2.427 5.781,2.625 0.771,0.198 10 false E117 2.896,0.583 3.938,0.813 1.042,0.229 10 false MPX-B NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION).



PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENSOR SOUND DETECT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.


f.

Make a metal-on-metal striking sound (such as by shaking keys) near the intrusion sensor and check the Data List.

Main Body (Main Body ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Intrusion Sensor Sound Detect*1*2 Sound detection status of the intrusion sensor (theft warning ultrasonic sensor) / ON or OFF ON: Sound detected
OFF: Sound not detected
Only displays "ON" on the Data List once. When checking again, disconnect and reconnect the GTS.

*1: w/o Door Ajar Warning Buzzer Function


NOTICE:
·

*2: Perform the intrusion sensor operation inspection with the GTS disconnected (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM (w/ Entry and Start System)>SYSTEM DESCRIPTION).

·

Make sure all the windows are closed



HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).


OK:

The GTS display changes correctly in response to the detection condition of the intrusion sensor (theft warning ultrasonic sensor).



g.

From inside the vehicle, put your hand in front of the sensor and move it back and forth a distance of 0.3 m (0.984 ft.) and check the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Intrusion Sensor Status of the intrusion sensor detection (theft warning ultrasonic sensor) / ON or OFF ON: Intrusion sensor detected
OFF: Intrusion sensor not detected
-

HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).


OK:

The GTS display changes correctly in response to the detection condition of the intrusion sensor (theft warning ultrasonic sensor).




OK

NG

2.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (IOUT)
2.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (IOUT)
a.

Using an oscilloscope, check the waveform.

U164404E01
3.453,0.088 3.806,0.252 0.352,0.164 10 R7 1.919,1.299 2.681,1.474 0.762,0.175 10 IOUT 3.965,3.176 4.727,3.351 0.762,0.175 10 *e 3.965,2.588 4.727,2.763 0.762,0.175 10 *d 2.041,3.185 2.803,3.361 0.762,0.175 10 *f 2.517,3.185 3.279,3.361 0.762,0.175 10 *g 2.601,3.54 3.363,3.716 0.762,0.175 10 *d 2.171,2.597 2.933,2.772 0.762,0.175 10 *c 1.648,2.597 2.410,2.772 0.762,0.175 10 *b 1.471,4.073 2.233,4.248 0.762,0.175 10 *i 3.974,4.073 4.736,4.248 0.762,0.175 10 *j 1.069,2.91 1.831,3.085 0.762,0.175 10 LO 1.069,2.449 1.831,2.624 0.762,0.175 10 HI 2.337,2.655 2.443,2.708 false 1.809,2.655 1.915,2.708 false 2.335,1.361 3.159,0.966 false

Text in Illustration
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State

Measurement Condition
Tester Connection Content
Tester Connection R7-12 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEXNETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU [MULTIPLEXNETWORK BODY ECU]

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEXNETWORK BODY ECU] - MAP LIGHT ASSEMBLY)
a.

Disconnect the E117 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-12 (ISIF) - R7- 12 (IOUT) Always Below 1 Ω
E117-12 (ISIF) - Body ground Always 10 kΩ or higher
R7-12 (IOUT) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MAP LAMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LAMP ASSEMBLY

b.

Remove the intrusion sensor (theft warning ultrasonic sensor) from the map light assembly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>INTRUSION SENSOR>REMOVAL).


c.
U164385E02
1.177,0.625 1.271,0.625 1.271,0.625 1.521,0.979 true 2.177,1.438 2.063,1.438 2.063,1.438 1.906,1.083 true 1.448,2.958 1.531,2.958 1.531,2.958 1.969,2.396 true 2.323,2.969 2.417,2.969 2.417,2.969 2.552,2.542 true 2.75,1.823 2.625,1.823 2.625,1.823 2.469,2.302 true 2.24,0.5 2.115,0.5 2.115,0.5 1.792,0.958 true 1.667,1.75 2.146,1.969 0.479,0.219 10 false B 2.219,1.354 2.698,1.573 0.479,0.219 10 false GND 1.99,2.906 2.469,3.125 0.479,0.219 10 false GND 1.104,2.885 1.583,3.104 0.479,0.219 10 false IOUT 2.781,1.76 3.26,1.979 0.479,0.219 10 false +B2 0.885,0.531 1.365,0.75 0.479,0.219 10 false +B2 1.646,0.438 2.125,0.656 0.479,0.219 10 false A 2.292,0.417 2.792,0.688 0.5,0.271 10 false IOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) -B-19 (GND) Always Below 1 Ω
A-2 (IOUT) -B-6 (IOUT) Always Below 1 Ω
A-4 (+B2) - B-2 (+B2) Always Below 1 Ω




OK

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG