Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Tilt Sensor Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) operates the theft warning tilt sensor (yaw rate sensor) via the CSIF communication line. The theft warning tilt sensor (yaw rate sensor) sends information regarding changes in the vehicle tilt angle to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) checks whether the vehicle body is being tilted without authorization.


WIRING DIAGRAM

B312497E24
5.615,1.781 6.083,2.063 0.469,0.281 10 false GCS 5.354,3.063 7.021,3.531 1.667,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 5.333,2.885 5.823,3.125 0.49,0.24 10 false E117 3.458,1.74 3.906,1.979 0.448,0.24 10 false CSIF 1.25,2.667 1.656,2.885 0.406,0.219 10 false E50 1.229,2.844 4.354,3.156 3.125,0.313 10 false Theft Warning Tilt Sensor (Yaw Rate Sensor) 1.365,1.781 1.917,1.99 0.552,0.208 10 false GND 1.198,1.635 1.51,1.927 0.313,0.292 10 false 1 1.75,0.271 2.833,0.604 1.083,0.333 10 false from Battery 5.417,1.646 5.604,1.875 0.188,0.229 10 false 6 3.885,1.615 4.063,1.813 0.177,0.198 10 false 5 3.594,1.219 3.906,1.438 0.313,0.219 10 false +B 3.875,1.125 4.063,1.313 0.188,0.188 10 false 6 3.552,0.427 4.385,0.823 0.833,0.396 10 false J/B-B NO.2

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION).



PROCEDURE

1.READ VALUE USING GTS (TILT SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tilt Sensor Status of the tilt sensor detection / ON or OFF ON: Theft warning tilt sensor detected
OFF: Theft warning tilt sensor not detected
-

NOTICE:

After setting the theft deterrent system, wait 30 seconds or more (until the vehicle is in the armed state), tilt the vehicle and confirm the Data List (jack up the vehicle so that the tires are in the air).


HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).


OK:

The display on the GTS changes according to the detection condition of the theft warning tilt sensor (yaw rate sensor).




OK

NG

2.CHECK THEFT WARNING TILT SENSOR (YAW RATE SENSOR) (CSIF)
2.CHECK THEFT WARNING TILT SENSOR (YAW RATE SENSOR) (CSIF)
a.

Using an oscilloscope, check the waveform.

U164281E01
1.683,0.122 1.857,0.296 0.174,0.174 10 *a 3.425,0.157 3.839,0.437 0.414,0.280 10 E117 4.868,1.803 5.459,1.977 0.591,0.174 10 GCS 1.625,2.666 1.799,2.840 0.174,0.174 10 *b 1.26,2.456 1.610,2.630 0.350,0.174 10 HI 1.26,2.909 1.652,3.083 0.392,0.174 10 LO 2.157,2.666 2.331,2.840 0.174,0.174 10 *c 3.974,2.634 4.148,2.808 0.174,0.174 10 *d 3.974,3.108 4.148,3.282 0.174,0.174 10 *e 2.101,3.183 2.275,3.357 0.174,0.174 10 *f 2.512,3.192 2.686,3.367 0.174,0.174 10 *g 2.654,3.538 2.829,3.712 0.174,0.174 10 *h 1.513,4.098 1.687,4.273 0.174,0.174 10 *i 3.95,4.098 4.125,4.273 0.174,0.174 10 *j 4.273,1.046 4.83,1.828 false 2.447,2.816 2.314,2.732 false 1.915,2.816 1.783,2.732 false

Text in Illustration
*a Component with harness connected
(Main body ECU [multiplex network body ECU])
*b CSIF Initial Signal
*c CSIF Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State

Measurement Condition
Tester Connection Content
Tester Connection E117-6 (GCS) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the theft warning tilt sensor (yaw rate sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING TILT SENSOR (YAW RATE SENSOR) -MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING TILT SENSOR (YAW RATE SENSOR) -MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the E50 theft warning tilt sensor (yaw rate sensor) connector.


b.

Disconnect the E117 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E50-5 (CSIF) - E117-6 (GCS) Always Below 1 Ω
E50-1 (GND) - Body ground Always Below 1 Ω
E50-5 (CSIF) - Body ground Always 10 kΩ or higher
E117-6 (GCS) - Body ground Always 10 kΩ or higher




OK

REPLACE THEFT WARNING TILT SENSOR (YAW RATE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR