Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the driver door only, but the entry lock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the unlock sensor (connection between the certification ECU [smart key ECU assembly] and front door outside handle assembly [for driver door]).

WIRING DIAGRAM

B388637E63
1.302,0.76 1.917,0.958 0.615,0.198 10 false ANT1 1.313,1.906 1.927,2.104 0.615,0.198 10 false ANT2 5.302,0.76 5.917,0.958 0.615,0.198 10 false CLG1 5.302,1.906 5.917,2.104 0.615,0.198 10 false CG1B 5.854,1.177 6.469,1.375 0.615,0.198 10 false IC 6.271,2.031 6.583,2.354 0.313,0.323 10 false E 6.469,1.906 6.781,2.229 0.313,0.323 10 false 11 5.125,2.583 5.74,2.781 0.615,0.198 10 false E130 5.125,2.75 6.688,3.271 1.563,0.521 10 false Certification ECU (Smart Key ECU Assembly) 5.125,1.906 5.438,2.229 0.313,0.323 10 false 3 5.125,0.76 5.438,1.083 0.313,0.323 10 false 4 1.76,0.76 2.073,1.083 0.313,0.323 10 false 6 1.781,1.906 2.094,2.229 0.313,0.323 10 false 4 0.448,2.583 1.292,2.76 0.844,0.177 10 false z76*1, z75*2 0.417,2.75 2.688,3.281 2.271,0.531 10 false Front Door Outside Handle Assembly (for Driver Door) 3.271,2.844 3.99,3.042 0.719,0.198 10 false *1: for LHD 3.271,3.24 3.99,3.438 0.719,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING GTS (FL DOOR LOCK POS)

NG

2.READ VALUE USING GTS (FL DOOR LOCK POS)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal*1 / UNLOCK or LOCK UNLOCK: Front door RH unlocked
LOCK: Front door RH locked
-
FL Door Lock Pos Front door LH unlock detection switch signal*2 / UNLOCK or LOCK UNLOCK: Front door LH unlocked
LOCK: Front door LH locked
-

*1: for RHD

*2: for LHD


OK:

The GTS display changes correctly in response to the lock/unlock operation of the driver door.



OK

3.READ VALUE USING GTS (D-DOOR TOUCH SENSOR)

NG

3.READ VALUE USING GTS (D-DOOR TOUCH SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.


Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D-Door Touch Sensor Driver door touch sensor (unlock sensor) / ON or OFF ON: Driver door touch sensor (unlock sensor) touched
OFF: Driver door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.



OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE ASSEMBLY [FOR DRIVER DOOR])
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE ASSEMBLY [FOR DRIVER DOOR])

*1: for LHD

*2: for RHD


a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the z76*1 or z75*2 front door outside handle assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
E130-4 (CLG1) - z76-6 (ANT1) Always Below 1 Ω
E130-3 (CG1B) - z76-4 (ANT2) Always Below 1 Ω
E130-4 (CLG1) or z76-6 (ANT1) - Body ground Always 10 kΩ or higher
E130-3 (CG1B) or z76-4 (ANT2) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
E130-4 (CLG1) - z75-6 (ANT1) Always Below 1 Ω
E130-3 (CG1B) - z75-4 (ANT2) Always Below 1 Ω
E130-4 (CLG1) or z75-6 (ANT1) - Body ground Always 10 kΩ or higher
E130-3 (CG1B) or z75-4 (ANT2) - Body ground Always 10 kΩ or higher



d.

Reconnect the z76*1 or z75*2 front door outside handle assembly (for driver door) connector.


e.

Reconnect the E130 certification ECU (smart key ECU assembly) connector.



OK

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (DRIVER DOOR) (INPUT TO DRIVER DOOR UNLOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (DRIVER DOOR) (INPUT TO DRIVER DOOR UNLOCK SENSOR)
U164330E02
5.74,1.271 5.667,2.219 true 6.031,1.375 6.375,2 true 0.188,0.073 0.406,0.271 0.219,0.198 10 false *a 0.958,2.698 1.177,2.896 0.219,0.198 10 false *b 0.896,4.365 1.115,4.563 0.219,0.198 10 false *c 1.646,4.458 1.865,4.656 0.219,0.198 10 false *d 2.375,4.385 2.594,4.583 0.219,0.198 10 false *c 0.74,3.688 1.104,3.854 0.365,0.167 10 false GND 6.365,2 6.5,2.167 0.135,0.167 10 false E 5.51,2.208 5.896,2.417 0.385,0.208 10 false CLG1 1.74,0.448 2.135,0.719 0.396,0.271 10 false E128 5.135,0.448 5.604,0.74 0.469,0.292 10 false E130 3.354,0.448 3.833,0.688 0.479,0.24 10 false E129

Text in Illustration
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform 1
*c Unlock sensor not touched *d Unlock sensor touched

a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
E130-4 (CLG1) - E130-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor touched


5 V/DIV., 50 ms/DIV. Pulse generation (See waveform 1)




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FRONT DRIVER DOOR)