Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
Use the same procedure for RHD and LHD vehicles.
The procedures listed below are for LHD vehicles.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
75072A
3.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)
67492A
4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
Detach the clip and claw, and remove the front door lower frame bracket garnish LH.
81230
5.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
69278B
6.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH
Using a screwdriver, detach the 4 claws and remove the front door inside handle bezel LH.
Tape the screwdriver tip before use.
|
Protective Tape |
74232
7.REMOVE FRONT UPPER ARMREST BASE PANEL LH
84040
8.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
74646
9.REMOVE DOOR ASSIST GRIP COVER LH
Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.
67602
10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
Remove the 13 clips.
Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.
Make sure that the pin labeled A in the illustration is detached from the door panel.
Disconnect the each connector.
Disconnect the 2 cables from the front door inside handle sub-assembly LH.
68172A
11.REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH
Detach the 4 clips and remove the front inner door glass weatherstrip LH from the front door trim board sub-assembly LH.
Squeeze the metal clip to remove it.
The metal clip may be deformed if it is forcibly pulled.
84927
12.REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)
69206B
13.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Detach the 2 claws and remove the front door inside handle sub-assembly LH.
69278E
14.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH
Disconnect the connector.
Remove the 8screws and front door inside handle bezel LH.
82505A
15.REMOVE FRONT DOOR WIRING SUB-ASSEMBLY
Detach the 2 clamps and remove the front door wiring sub-assembly.
87940
16.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
89430
17.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)
67856B
18.REMOVE FRONT DOOR PANEL PROTECTOR LH
Remove the screw, and remove the front No. 1 door stiffener cushion and front door panel protector LH.
86160
19.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
89860A
20.REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH (w/ Curtain Shield Airbag)
67832
21.REMOVE FRONT DOOR SERVICE HOLE COVER LH
Using a clip remover, detach the 9 clamps.
Remove the bolt and disconnect the 2 connectors.
Remove the front door service hole cover LH.
Remove the remaining tape on the door.
68102
22.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Driver Side:
Temporarily install the multiplex network master switch.
Passenger Side:
Temporarily install the power window regulator switch assembly.
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly until the bolts appear in the service holes.
Disconnect the cable from the negative (-) battery terminal.
Remove the 2 bolts.
Be careful when removing the bolts as the glass may fall and become damaged.
Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.
Remove the front door glass sub-assembly upward.
Be careful not to damage the glass.
Driver Side:
Remove the multiplex network master switch.
Passenger Side:
Remove the power window regulator switch assembly.
68151E
23.REMOVE FRONT DOOR GLASS RUN LH
Remove the front door glass run LH.
67404F
24.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Remove the bolt.
Detach the guide and front door rear lower frame sub-assembly LH.
67674
25.REMOVE LOWER DOOR FRAME GARNISH LH
Detach the claw and remove the lower door frame garnish LH.
75720
26.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH
75756C
27.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH
69802
28.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Loosen the temporary bolt.
| *a | Temporary Bolt |
Remove the 5 bolts, and front door window regulator sub-assembly LH.
Remove the front door window regulator sub-assembly LH through the service hole.
Be careful when removing the bolts as the front door window regulator sub-assembly LH may fall and become damaged.
Remove the front door window regulator sub-assembly LH and the front power window regulator motor assembly LH as a unit.
Remove the temporary bolt from the front door window regulator sub-assembly LH.
85720C
29.REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
69217F
30.REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH
Remove the hole plug.
Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock cylinder installed.
Detach the 2 claws and remove the front door outside handle cover LH.
69220
31.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
w/ Entry and Start System:
Using a screwdriver, detach the 2 claws of the connector cover in the direction indicated and disconnect the connector cover.
Tape the screwdriver tip before use.
|
Protective Tape |
Using a screwdriver, detach the 2 claws of the connector in the direction indicated and disconnect the connector.
Tape the screwdriver tip before use.
|
Protective Tape |
Detach the 2 claws and remove the holder in the direction indicated by the arrow in the illustration.
Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.
If the release plate is not pulled and held when removing the front door outside handle assembly LH, the release plate will interfere with the front door outside handle assembly LH and become damaged.
69252
32.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH
Detach the 3 claws and remove the front door front outside handle pad LH.
69254C
33.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH
Detach the 2 claws and remove the front door rear outside handle pad LH.
69320
34.REMOVE FRONT DOOR LOCK ASSEMBLY LH
69720B
35.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
Remove the front door lock remote control cable assembly LH.
69760C
36.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH
Using a screwdriver, detach the 3 claws.
Tape the screwdriver tip before use.
|
Protective Tape |
Remove the front door inside locking cable assembly LH.
69202A
37.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Using a T30 "TORX" wrench, loosen the screw.
| *a | Clamp |
| *b | Nut |
| *c | Guide |
w/ Entry and Start System:
Detach the clamp.
Detach the nut and 2 guides and remove the front door outside handle frame sub-assembly LH in the direction indicated by the arrow in the illustration.
89746D
38.REMOVE NO. 2 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)
Detach the 2 clamps and guide and remove the No. 2 electrical key wire harness from the front door outside handle frame sub-assembly LH.
| *a | Guide |
| *b | Clamp |
69312
39.REMOVE FRONT DOOR LOCK OPEN ROD LH
Remove the front door lock open rod LH.
67924
40.REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION
Remove the 2 bolts.
Detach the 2 clamps and front No. 2 door stiffener cushion.
68620
41.REMOVE FRONT DOOR CHECK ASSEMBLY LH
Remove the bolt, 2 nuts and front door check assembly LH.
Be careful when removing the bolt and nuts as the front door check assembly LH may fall and become damaged.
Remove the front door check assembly LH through the service hole.
67862
42.REMOVE FRONT DOOR WEATHERSTRIP LH
Using a clip remover, detach the 21 clips and remove the front door weatherstrip LH.
If clips are damaged during removal, replace them.
| *A | w/ Spot Cover | *B | w/o Spot Cover |
| *1 | Double-sided Tape | - | - |