Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Rear Door LH Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the rear door LH only, but the entry lock function operates, the request code is being transmitted properly from the rear door LH. In this case, there may be a problem related to the unlock sensor (connection between the certification ECU [smart key ECU assembly] and rear door outside handle assembly LH).

WIRING DIAGRAM

for LHD:

B449203E02
1.302,0.781 1.667,0.948 0.365,0.167 10 false ANT1 1.313,1.917 1.677,2.083 0.365,0.167 10 false ANT2 1.75,0.76 1.854,0.927 0.104,0.167 10 false 6 1.75,1.885 1.854,2.052 0.104,0.167 10 false 4 4.906,0.865 5.271,1.031 0.365,0.167 10 false E129 4.906,2.01 5.271,2.177 0.365,0.167 10 false E129 5.021,0.656 5.125,0.823 0.104,0.167 10 false 8 5.031,1.802 5.135,1.969 0.104,0.167 10 false 7 5.313,0.771 5.677,0.938 0.365,0.167 10 false CLG3 5.313,1.917 5.677,2.083 0.365,0.167 10 false CG3B 5.813,1.438 6.021,1.604 0.208,0.167 10 false IC 6.25,2.021 6.458,2.188 0.208,0.167 10 false E 6.521,1.813 6.729,1.979 0.208,0.167 10 false 11 6.458,2.021 6.823,2.188 0.365,0.167 10 false E130 0.698,2.531 1.063,2.698 0.365,0.167 10 false z78 0.688,2.698 2.542,3.333 1.854,0.635 10 false Rear Door Outside Handle Assembly LH 5.094,2.542 6.646,3.188 1.552,0.646 10 false Certification ECU (Smart Key ECU Assembly)

for RHD:

B449304E02
1.333,0.771 1.708,0.948 0.375,0.177 10 false ANT1 1.333,1.917 1.708,2.094 0.375,0.177 10 false ANT2 1.75,0.76 2.125,0.938 0.375,0.177 10 false 6 1.781,1.906 2.156,2.083 0.375,0.177 10 false 4 4.906,0.875 5.281,1.052 0.375,0.177 10 false E129 4.906,2.01 5.281,2.188 0.375,0.177 10 false E129 4.969,0.656 5.344,0.833 0.375,0.177 10 false 10 4.99,1.813 5.365,1.99 0.375,0.177 10 false 9 5.302,0.792 5.677,0.969 0.375,0.177 10 false CLG4 5.302,1.927 5.677,2.104 0.375,0.177 10 false CG4B 5.813,1.396 5.99,1.594 0.177,0.198 10 false IC 6.25,2.021 6.427,2.219 0.177,0.198 10 false E 6.458,2.021 6.833,2.188 0.375,0.167 10 false E130 6.531,1.771 6.708,1.969 0.177,0.198 10 false 11 0.646,2.563 1.021,2.74 0.375,0.177 10 false z78 0.635,2.719 2.313,3.292 1.677,0.573 10 false Rear Door Outside Handle Assembly LH 5.083,2.573 6.76,3.146 1.677,0.573 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING GTS (RL-DOOR LOCK POS SW)

NG

2.READ VALUE USING GTS (RL-DOOR LOCK POS SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL-Door Lock Pos SW Rear door LH unlock detection switch signal / ON or OFF ON: Rear door LH unlocked
OFF: Rear door LH locked
-

OK:

The GTS display changes correctly in response to the lock/unlock operation of the rear door LH.



OK

3.READ VALUE USING GTS (DL-DOOR TOUCH SENSOR)

NG

3.READ VALUE USING GTS (DL-DOOR TOUCH SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG)


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.


Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Dr-Door Touch Sensor Rear door LH touch sensor (unlock sensor)*1 / ON or OFF ON: Rear door LH touch sensor (unlock sensor) touched
OFF: Rear door LH touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Pr-Door Touch Sensor Rear door LH touch sensor (unlock sensor)*2 / ON or OFF ON: Rear door LH touch sensor (unlock sensor) touched
OFF: Rear door LH touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.



*1: for LHD

*2: for RHD


OK:

The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH.



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the z78 rear door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
E129-8 (CLG3) - z78-6 (ANT1) Always Below 1 Ω
E129-7 (CG3B) - z78-4 (ANT2) Always Below 1 Ω
E129-8 (CLG3) or z78-6 (ANT1) - Body ground Always 10 kΩ or higher
E129-7 (CG3B) or z78-4 (ANT2) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
E129-10 (CLG4) - z78-6 (ANT1) Always Below 1 Ω
E129-9 (CG4B) - z78-4 (ANT2) Always Below 1 Ω
E129-10 (CLG4) or z78-6 (ANT1) - Body ground Always 10 kΩ or higher
E129-9 (CG4B) or z78-4 (ANT2) - Body ground Always 10 kΩ or higher



d.

Reconnect the z78 rear door outside handle assembly LH connector.


e.

Reconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.



OK

5.CHECK REAR DOOR OUTSIDE HANDLE ASSEMBLY LH (INPUT TO REAR DOOR LH UNLOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK REAR DOOR OUTSIDE HANDLE ASSEMBLY LH (INPUT TO REAR DOOR LH UNLOCK SENSOR)
U164332E02
2.969,1.229 3.042,2.146 true 2.75,1.26 2.333,2.146 true 6.021,1.375 6.365,2 true 0.188,0.073 0.406,0.271 0.219,0.198 10 false *a 0.958,2.781 1.177,2.979 0.219,0.198 10 false *b 0.896,4.365 1.115,4.563 0.219,0.198 10 false *c 1.646,4.448 1.865,4.646 0.219,0.198 10 false *d 2.344,4.385 2.563,4.583 0.219,0.198 10 false *c 0.729,3.688 1.094,3.854 0.365,0.167 10 false GND 6.354,2.021 6.49,2.188 0.135,0.167 10 false E 2.802,2.167 3.427,2.333 0.625,0.167 10 false CLG3*A 2.083,2.177 2.708,2.344 0.625,0.167 10 false CLG4*B 1.74,0.458 2.115,0.698 0.375,0.24 10 false E128 5.135,0.438 5.552,0.677 0.417,0.24 10 false E130 3.344,0.458 3.76,0.656 0.417,0.198 10 false E129

Text in Illustration
*A for LHD *B for RHD
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform 1
*c Unlock sensor not touched *d Unlock sensor touched

a.

Using an oscilloscope, check the waveform.

OK:
for LHD
Tester Connection Switch Condition Tool Setting Specified Condition
E129-8 (CLG3) - E130-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door LH unlock sensor touched


5 V/DIV., 50 ms/DIV. Pulse generation (See waveform 1)

for RHD
Tester Connection Switch Condition Tool Setting Specified Condition
E129-10 (CLG4) - E130-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door LH unlock sensor touched


5 V/DIV., 50 ms/DIV. Pulse generation (See waveform 1)




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH