Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Rear Door LH Entry Lock Function does not Operate  


DESCRIPTION

If the rear door LH entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → rear door outside handle LH (entry lock switch) → rear door electrical key oscillator LH).

HINT:

For vehicles with entry function for rear doors.


WIRING DIAGRAM

B186276E07
5.473,1.423 5.778,1.599 0.305,0.176 10 E30 3.005,1.423 3.258,1.592 0.253,0.169 10 z27 0.13,1.423 0.393,1.593 0.263,0.170 10 z28 0.13,2.218 1.470,2.388 1.339,0.170 10 *1: for LHD 0.13,2.477 1.470,2.647 1.339,0.170 10 *2: for RHD 5.848,0.385 6.389,0.534 0.541,0.149 10 TSW3*1 3.58,0.444 3.986,0.641 0.406,0.198 10 TRG+ 3.15,0.917 3.514,1.115 0.364,0.198 10 TRG- 0.936,0.917 1.314,1.115 0.378,0.198 10 TRG- 1.405,1.037 1.525,1.248 0.120,0.211 10 9 4.102,0.546 4.208,0.758 0.106,0.211 10 3 5.473,0.385 5.777,0.542 0.304,0.157 10 25*1 3.005,1.023 3.124,1.234 0.119,0.211 10 1 5.473,1.62 7.040,1.970 1.567,0.351 10 Certification ECU (Smart Key ECU Assembly) 3.005,1.592 4.886,1.980 1.881,0.388 10 Rear Door Outside Handle LH 0.13,1.592 2.522,1.948 2.392,0.357 10 Door Electrical Key Oscillator 5.848,0.561 6.389,0.709 0.541,0.149 10 TSW4*2 5.473,0.561 5.777,0.718 0.304,0.157 10 26*2

PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the master switch assembly door control switch is operated, check that the locked doors unlock.

OK:

Door locks operate normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

i.

for LHD

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
DR Door Lock Position SW Driver side rear door lock position switch signal / ON or OFF ON: Driver side rear door unlocked
OFF: Driver side rear door locked
-

OK:

On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



ii.

for RHD

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PR Door Lock Position SW Passenger side rear door lock position switch signal / ON or OFF ON: Passenger side rear door unlocked
OFF: Passenger side rear door locked
-

OK:

On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.





OK

3.READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Rear Door LH LOCK/UNLOCK Functions do not Operate)

3.READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH)
a.

Using the intelligent tester, read the Data List.

i.

for LHD

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Dr-Door Trigger Switch Driver side rear door outside handle lock switch / ON or OFF ON: Entry lock switch pushed
OFF: Entry lock switch not pushed
-

OK:

On tester screen, item changes between ON and OFF according to above chart.



ii.

for RHD

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Pr-Door Trigger Switch Passenger side rear door outside handle lock switch / ON or OFF ON: Entry lock switch pushed
OFF: Entry lock switch not pushed
-

OK:

On tester screen, item changes between ON and OFF according to above chart.





OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (REAR DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)
4.CHECK HARNESS AND CONNECTOR (REAR DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)
a.

Disconnect the z28 oscillator connector.

B449202E06
1.885,1.354 1.302,1.906 true 5.813,2.052 5.458,1.604 true 0.063,0.031 2.323,0.385 2.26,0.354 10 false Front view of wire harness connector: (to Rear Door Outside Handle) 3.99,0.031 6.25,0.385 2.26,0.354 10 false Front view of wire harness connector: (to Door Electrical Key Oscillator) 1.021,1.302 1.271,1.469 0.25,0.167 10 false z27 4.229,1.271 4.479,1.438 0.25,0.167 10 false z28 1.094,1.917 1.542,2.146 0.448,0.229 10 false TRG- 5.729,2.083 6.177,2.313 0.448,0.229 10 false TRG-


b.

Disconnect the z27 handle connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z28-9 (TRG-) - z27-1 (TRG-) Always Below 1 Ω
z28-9 (TRG-) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE)
a.

Disconnect the E30 ECU connector.

B449328E01
2.49,1.833 2.271,2.313 true 2.667,1.844 2.885,2.313 true 5.229,1.563 4.76,2.281 true 1.833,1 2.292,1.198 0.458,0.198 10 false E30 4.427,0.99 4.885,1.188 0.458,0.198 10 false z27 0.042,0.031 2.406,0.583 2.365,0.552 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 4.188,0.031 6.552,0.583 2.365,0.552 10 false Front view of wire harness connector: (to Rear Door Outside Handle) 2,2.344 2.646,2.552 0.646,0.208 10 false TSW3*1 2.729,2.344 3.375,2.552 0.646,0.208 10 false TSW4*2 4.531,2.313 5.177,2.521 0.646,0.208 10 false TRG+ 0.063,2.104 0.896,2.281 0.833,0.177 10 false *1: for LHD 0.083,2.385 0.917,2.563 0.833,0.177 10 false *2: for RHD


b.

Disconnect the z27 handle connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
E30-25 (TSW3) - z27-3 (TRG+) Always Below 1 Ω
E30-25 (TSW3) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
E30-26 (TSW4) - z27-3 (TRG+) Always Below 1 Ω
E30-26 (TSW4) - Body ground Always 10 kΩ or higher




OK

6.INSPECT REAR DOOR OUTSIDE HANDLE LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR DOOR OUTSIDE HANDLE LH
a.
U164007E01
0.536,2.174 0.903,2.342 0.366,0.169 10 TRG- 2.406,2.353 2.805,2.522 0.400,0.169 10 TRG+ 1.656,2.667 1.033,2.265 false 0.211,1.256 2.712,1.563 2.501,0.307 10 Component without harness connected: (Rear Door Outside Handle) 2.404,2.606 2.671,2.756 0.267,0.150 10 z27 1.786,2.816 2.37,2.414 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
z27-1 (TRG-) - z27-3 (TRG+) Lock switch not pushed 10 kΩ or higher
Lock switch pushed Below 1 Ω




OK

7.REPLACE DOOR ELECTRICAL KEY OSCILLATOR

NG

7.REPLACE DOOR ELECTRICAL KEY OSCILLATOR
a.

Replace the door electrical key oscillator (See page Vehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY).



NEXT

8.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
8.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
a.

Check that the entry function operates normally.

OK:

Operates normally.




OK

END (DOOR ELECTRICAL OSCILLATOR IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)