If the rear door RH entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → rear door outside handle RH (entry lock switch) → rear door electrical key oscillator RH).
For vehicles with entry function for rear doors.
When the master switch assembly door control switch is operated, check that the locked doors unlock.
Door locks operate normally.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
for LHD
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| PR Door Lock Position SW | Passenger side rear door lock position switch signal / ON or OFF | ON: Passenger side rear door unlocked
OFF: Passenger side rear door locked |
- |
On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
for RHD
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| DR Door Lock Position SW | Driver side rear door lock position switch signal / ON or OFF | ON: Driver side rear door unlocked
OFF: Driver side rear door locked |
- |
On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
OK
NG
Using the intelligent tester, read the Data List.
for LHD
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Pr-Door Trigger Switch | Passenger side rear door outside handle lock switch / ON or OFF | ON: Entry lock switch pushed
OFF: Entry lock switch not pushed |
- |
On tester screen, item changes between ON and OFF according to above chart.
for RHD
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Dr-Door Trigger Switch | Driver side rear door outside handle lock switch / ON or OFF | ON: Entry lock switch pushed
OFF: Entry lock switch not pushed |
- |
On tester screen, item changes between ON and OFF according to above chart.
OK
NG
Disconnect the z26 oscillator connector.
Disconnect the z25 handle connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z26-9 (TRG-) - z25-1 (TRG-) | Always | Below 1 Ω |
| z26-9 (TRG-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the E30 ECU connector.
Disconnect the z25 handle connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E30-26 (TSW4) - z25-3 (TRG+) | Always | Below 1 Ω |
| E30-26 (TSW4) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E30-25 (TSW3) - z25-3 (TRG+) | Always | Below 1 Ω |
| E30-25 (TSW3) - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z25-1 (TRG-) - z25-3 (TRG+) | Lock switch not pushed | 10 kΩ or higher |
| Lock switch pushed | Below 1 Ω |
OK
NG
(See pageVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH (for Rear)>REMOVAL)
Replace the door electrical key oscillator (See page Vehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY).
NEXT
Check that the entry function operates normally.
Operates normally.
OK
NG