Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Room Oscillator does not Recognize Key  


DESCRIPTION

If the room oscillator does not recognize the key, one of the following may be the cause: 1) communication between the indoor electrical key antenna (for Front) and electrical key transmitter cannot be performed; or 2) communication between the indoor electrical key antenna (for Rear 1) and electrical key transmitter cannot be performed; or 3) communication between the indoor electrical key antenna (for Rear 2) and electrical key transmitter cannot be performed.

WIRING DIAGRAM

B144447E07
0.271,1.792 2.813,1.979 2.542,0.188 10 false Indoor Electrical Key Antenna (for Front) 0.25,3.938 2.896,4.125 2.646,0.188 10 false Indoor Electrical Key Antenna (for Rear 1) 0.25,6.063 2.865,6.271 2.615,0.208 10 false Indoor Electrical Key Antenna (for Rear 2) 5.438,5.979 6.979,6.323 1.542,0.344 10 false Certification ECU (Smart Key ECU Assembly) 1.542,0.417 1.948,0.594 0.406,0.177 10 false CLG3 2.125,0.635 2.354,0.865 0.229,0.229 10 false 1 1.542,1.031 1.948,1.208 0.406,0.177 10 false CLGB 2.125,1.25 2.354,1.479 0.229,0.229 10 false 3 1.552,2.573 1.958,2.75 0.406,0.177 10 false CLG4 2.115,2.76 2.344,2.99 0.229,0.229 10 false 1 1.552,3.188 1.958,3.365 0.406,0.177 10 false CLGB 2.125,3.406 2.354,3.635 0.229,0.229 10 false 2 1.531,4.688 1.938,4.865 0.406,0.177 10 false CLG6 2.104,4.906 2.333,5.146 0.229,0.24 10 false 1 1.531,5.292 1.938,5.469 0.406,0.177 10 false CLGB 2.125,5.5 2.354,5.729 0.229,0.229 10 false 2 5.646,0.531 6.052,0.708 0.406,0.177 10 false CLG5 5.344,0.625 5.573,0.854 0.229,0.229 10 false 11 5.667,1.156 6.073,1.333 0.406,0.177 10 false CG5B 5.333,1.25 5.563,1.479 0.229,0.229 10 false 12 5.656,2.677 6.063,2.854 0.406,0.177 10 false CLG6 5.313,2.76 5.542,2.99 0.229,0.229 10 false 13 5.667,3.313 6.073,3.49 0.406,0.177 10 false CG6B 5.333,3.396 5.563,3.625 0.229,0.229 10 false 14 5.667,4.781 6.073,4.958 0.406,0.177 10 false CLG7 5.333,4.865 5.563,5.094 0.229,0.229 10 false 15 5.656,5.396 6.063,5.573 0.406,0.177 10 false CG7B 5.344,5.51 5.573,5.74 0.229,0.229 10 false 16 5.438,5.833 5.75,5.99 0.313,0.156 10 false E29 0.25,5.906 0.521,6.094 0.271,0.188 10 false L9 0.25,3.781 0.521,3.969 0.271,0.188 10 false L8 0.26,1.646 0.49,1.833 0.229,0.188 10 false V3

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing the inspection, check that there are no problems related to the "CAN Communication System" and "LIN Communication System".

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the tester and vehicle begins.



PROCEDURE

1.CHECK ENTRY AND START SYSTEM (ENTRY FUNCTION)
a.

Check that the entry lock and unlock function can be operated at each door (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).



OK

2.CHECK ENTRY AND START SYSTEM (START FUNCTION)

NG

Go to DTC OF OTHER COMPONENTS (PROCEED TO PROBLEM SYMPTOM FLOWCHART FOR EACH DOOR)

2.CHECK ENTRY AND START SYSTEM (START FUNCTION)
a.
B311542E01
0.08,0.024 0.805,0.322 0.725,0.298 10 *A 0.08,2.086 0.805,2.384 0.725,0.298 10 *B 1.942,1.972 2.179,2.146 0.237,0.174 10 *1 2.509,2.728 2.746,2.902 0.237,0.174 10 *2 1.193,1.191 1.512,2.046 1.512,2.046 1.317,2.559 false 1.512,2.046 1.91,2.046 false 2.117,2.871 2.472,2.808 false 2.566,0.499 2.803,0.674 0.237,0.174 10 *2 2.174,0.642 2.529,0.579 false

Remove the battery of the electrical key transmitter (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>REMOVAL).


b.

With the brake pedal depressed, touch the key to the engine switch, as shown in the illustration.


c.

When operating the engine switch, check whether the power source mode changes.

OK:

Power source mode changes.


HINT:
·

When the electrical key transmitter cannot be verified even though it is in the operating range of the start function, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter and holding the transmitter against the engine switch.

·

When performing the check, if the power source mode changes, there is a problem with key certification inside the cabin.





OK

3.CHECK WAVE ENVIRONMENT

NG

3.CHECK WAVE ENVIRONMENT
a.

Install the battery to the electrical key transmitter (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>REMOVAL).


b.

Bring the electrical key transmitter near the indoor electrical key antenna (in center console), and perform an engine control system start check.

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the center console, communication is not possible.


OK:

Engine starts.



c.

Bring the electrical key transmitter near the indoor electrical key antenna (in rear No. 1 seat cushion), and perform an engine control system start check.

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the rear No. 1 seat cushion, communication is not possible.


OK:

Engine starts.



d.

Bring the electrical key transmitter near the indoor electrical key antenna (in rear No. 2 seat cushion), and perform an engine control system start check.

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the rear No. 2 seat cushion, communication is not possible.


HINT:
·

When the electrical key transmitter is brought near the indoor electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference, If installed, remove them and perform the operation check.



OK:

Engine starts.




OK

AFFECTED BY WAVE INTERFERENCE

NG

4.KEY DIAGNOSTIC MODE
4.KEY DIAGNOSTIC MODE
a.
B185377E01
2.379,0.157 3.076,0.500 0.697,0.343 10 Inspection Point 1.856,0.873 2.296,0.219 2.296,0.219 2.365,0.219 false

Diagnostic mode inspection (indoor electrical key antenna (for Front)).

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Front Room.


v.

When the electrical key transmitter is placed on the driver seat or front passenger seat cushion, check that the wireless door lock buzzer sounds.



b.
B185378E01
2.42,0.127 3.113,0.469 0.694,0.342 10 Inspection Point 1.847,0.871 2.265,0.191 2.265,0.191 2.402,0.191 false

Diagnostic mode inspection (indoor electrical key antenna (for Rear 1)).

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Rear Room.


v.

When the electrical key transmitter is placed on the rear seat cushion, check that the wireless door lock buzzer sounds.



c.
B185379E01
2.461,0.147 3.151,0.453 0.691,0.306 10 Inspection Point 1.863,0.896 2.31,0.241 2.31,0.241 2.439,0.241 false

Diagnostic mode inspection (indoor electrical key antenna (for Rear 2)).

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Back Door (inside) Room.


v.

When the electrical key transmitter is placed on the rear seat cushion, check that the wireless door lock buzzer sounds.



HINT:
·

If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.

·

It is possible to check which indoor electrical key antenna (front, rear 1 or rear 2) is operating by sounding the buzzer.

·

If the buzzer does not sound for any indoor electrical key antennas, the certification ECU (smart key ECU assembly) circuit may have a malfunction.



Result
Result Proceed to
Front operation check fails A
Rear 1 operation check fails B
Rear 2 operation check fails C
Front, rear 1 and rear 2 operation checks are normal or fail D


A

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

B

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

C

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

D

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)
U163878E02
2.604,1.323 2.167,2.063 true 2.729,1.323 2.969,2.073 true 5.396,1.448 4.948,2.021 true 5.656,1.448 6.146,2.01 true 0.802,0.104 3.74,0.469 2.938,0.365 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 4.219,0.104 6.531,0.51 2.313,0.406 10 false Front view of wire harness connector: (to Indoor Electrical Key Antenna) 0.333,1.156 0.604,1.323 0.271,0.167 10 false E29 4.698,1.156 4.948,1.365 0.25,0.208 10 false V3 1.979,2.083 2.385,2.25 0.406,0.167 10 false CLG5 2.875,2.073 3.281,2.24 0.406,0.167 10 false CG5B 4.729,2.042 5.25,2.24 0.521,0.198 10 false CLG3 6.021,2.031 6.427,2.198 0.406,0.167 10 false CLGB

a.

Disconnect the E29 ECU connector.


b.

Disconnect the V3 antenna connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V3-1 (CLG3) - E29-11 (CLG5) Always Below 1 Ω
V3-3 (CLGB) - E29-12 (CG5B) Always Below 1 Ω
V3-1 (CLG3) - Body ground Always 10 kΩ or higher
V3-3 (CLGB) - Body ground Always 10 kΩ or higher




OK

6.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Front Floor)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Front Floor)
U163932E02
1.052,1.26 0.604,1.958 true 1.115,1.26 1.271,2 true 0.406,2.01 0.813,2.188 0.406,0.177 10 false CG5B 1.094,2.01 1.5,2.188 0.406,0.177 10 false CLG5 6.479,1.156 6.844,1.333 0.365,0.177 10 false GND 0.385,0.094 3.375,0.448 2.99,0.354 10 false Component with harness connected: (Certification ECU [Smart Key ECU Assembly]) 1.26,0.771 1.531,0.948 0.271,0.177 10 false E29

a.

Measure the voltage according to the value(s) in the table below.

OK:
Tester Connection Tool Setting Switch Condition Specified Condition
E29-11 (CLG5) - E29-12 (CG5B) 2 V/DIV, 2 μsec./DIV. (Reference) Engine switch on (IG) Pulse generation




OK

REPLACE INDOOR ELECTRICAL KEY ANTENNA (for Front Floor)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)
U164043E02
5.448,1.385 5.656,1.906 true 5.302,1.365 5.094,1.917 true 2.917,1.313 3.115,1.865 true 2.802,1.313 2.604,1.865 true 0.677,0.063 3.656,0.427 2.979,0.365 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 4.396,0.063 6.76,0.521 2.365,0.458 10 false Front view of wire harness connector: (to Indoor Electrical Key Antenna) 0.281,1.177 0.604,1.354 0.323,0.177 10 false E29 4.458,1.177 4.781,1.354 0.323,0.177 10 false L8 4.906,1.917 5.344,2.135 0.438,0.219 10 false CLG4 5.51,1.917 5.948,2.135 0.438,0.219 10 false CLGB 2.396,1.885 2.833,2.104 0.438,0.219 10 false CLG6 2.958,1.875 3.396,2.094 0.438,0.219 10 false CG6B

a.

Disconnect the E29 ECU connector.


b.

Disconnect the L8 antenna connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L8-1 (CLG4) - E29-13 (CLG6) Always Below 1 Ω
L8-2 (CLGB) - E29-14 (CG6B) Always Below 1 Ω
L8-1 (CLG4) - Body ground Always 10 kΩ or higher
L8-2 (CLGB) - Body ground Always 10 kΩ or higher




OK

8.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 1 Floor)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 1 Floor)
U163933E02
1.01,1.26 0.563,1.958 true 1.063,1.25 1.104,1.948 true 0.333,2 0.74,2.177 0.406,0.177 10 false CG6B 0.927,2 1.333,2.177 0.406,0.177 10 false CLG6 6.5,1.156 6.885,1.385 0.385,0.229 10 false GND 0.458,0.01 3.448,0.365 2.99,0.354 10 false Component with harness connected: (Certification ECU [Smart Key ECU Assembly]) 1.25,0.76 1.521,0.938 0.271,0.177 10 false E29

a.

Measure the voltage according to the value(s) in the table below.

OK:
Tester Connection Tool Setting Switch Condition Specified Condition
E29-13 (CLG6) - E29-14 (CG6B) 2 V/DIV., 2 μsec./DIV. (Reference) Engine switch on (IG) Pulse generation




OK

REPLACE INDOOR ELECTRICAL KEY ANTENNA (for Rear 1 Floor)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)
U163879E02
5.635,1.427 5.885,1.906 true 5.417,1.427 5.167,1.906 true 3.146,1.323 3.406,1.958 true 3.01,1.313 2.75,1.948 true 0.531,0.042 3.448,0.406 2.917,0.365 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 4.281,0.052 6.594,0.469 2.313,0.417 10 false Front view of wire harness connector: (to Indoor Electrical Key Antenna) 0.323,1.156 0.594,1.323 0.271,0.167 10 false E29 4.719,1.344 5,1.552 0.281,0.208 10 false L9 2.521,1.99 2.927,2.156 0.406,0.167 10 false CLG7 3.24,1.99 3.646,2.156 0.406,0.167 10 false CG7B 4.958,1.958 5.479,2.156 0.521,0.198 10 false CLG6 5.74,1.938 6.146,2.104 0.406,0.167 10 false CLGB

a.

Disconnect the E29 ECU connector.


b.

Disconnect the L9 antenna connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L9-1 (CLG6) - E29-15 (CLG) Always Below 1 Ω
L9-2 (CLGB) - E29-16 (CG7B) Always Below 1 Ω
L9-1 (CLG6) - Body ground Always 10 kΩ or higher
L9-2 (CLGB) - Body ground Always 10 kΩ or higher




OK

10.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 2 Floor)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 2 Floor)
U163934E02
0.854,1.26 0.396,1.969 true 0.917,1.26 1.01,1.958 true 0.24,2.01 0.646,2.188 0.406,0.177 10 false CG7B 0.833,2.01 1.24,2.188 0.406,0.177 10 false CLG7 6.51,1.146 6.896,1.375 0.385,0.229 10 false GND 0.458,0 3.448,0.354 2.99,0.354 10 false Component with harness connected: (Certification ECU [Smart Key ECU Assembly]) 1.24,0.781 1.51,0.958 0.271,0.177 10 false E29

a.

Measure the voltage according to the value(s) in the table below.

OK:
Tester Connection Tool Setting Switch Condition Specified Condition
E29-15 (CLG7) - E29-16 (CG7B) 2 V/DIV., 2 μsec./DIV. (Reference) Engine switch on (IG) Pulse generation




OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)