Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Key Cannot be Registered  


DESCRIPTION

A maximum of 5 master key codes and 3 sub key codes can be registered.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.


PROCEDURE

1.CHECK REGISTRATION MODE
a.

Check that the system enters registration mode.

OK:

System enters registration mode




OK

2.CHECK SECURITY INDICATOR LIGHT OPERATION

NG

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

In registration mode, when the key is inserted in the ignition key cylinder, check that the security indicator light blinks in the normal pattern shown below.

HINT:

If the new key code registration fails, code 2-1 will be output through the security indicator light. Trying to reregister an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the security indicator light. The output details are shown below.


B111593E31
0.225,1.529 1.499,2.006 1.274,0.476 10 Normal (Immobiliser system is operating normally) 0.225,3.503 0.821,3.648 0.596,0.145 10 Code 2-1 0.225,5.631 0.814,5.768 0.589,0.137 10 Code 2-2 0.225,7.679 0.826,7.823 0.601,0.144 10 Code 2-3 2.026,0.675 2.612,0.830 0.586,0.156 10 0.12 sec. 2.901,2.037 3.495,2.177 0.593,0.140 10 1.88 sec. 1.689,1.27 1.949,1.422 0.260,0.152 10 On 1.658,1.708 1.980,1.857 0.323,0.149 10 Off 1.721,3.179 1.974,3.326 0.253,0.147 10 On 1.701,3.613 2.022,3.755 0.321,0.142 10 Off 1.735,5.259 2.016,5.399 0.281,0.140 10 On 1.71,5.701 2.040,5.843 0.330,0.142 10 Off 2.012,2.534 2.608,2.704 0.597,0.170 10 0.25 sec. 2.225,4.028 2.812,4.166 0.586,0.138 10 0.25 sec. 2.955,3.902 3.065,4.221 false 2.852,4.244 3.358,4.381 0.505,0.137 10 0.5 sec. 3.483,2.675 3.882,2.817 0.399,0.142 10 1 sec. 1.749,7.368 1.993,7.519 0.244,0.151 10 On 1.743,7.802 2.064,7.949 0.321,0.147 10 Off 2.054,4.625 2.675,4.764 0.621,0.139 10 0.25 sec. 3.849,4.839 4.244,4.979 0.395,0.140 10 1 sec. 2.183,6.142 2.770,6.282 0.586,0.140 10 0.25 sec. 2.954,5.999 3.066,6.31 false 2.817,6.314 3.327,6.455 0.510,0.141 10 0.5 sec. 2.04,6.702 2.636,6.865 0.597,0.163 10 0.25 sec. 2.204,8.244 2.798,8.411 0.593,0.167 10 0.25 sec. 4.188,6.914 4.582,7.057 0.393,0.143 10 1 sec. 2.961,8.098 3.082,8.445 false 2.833,8.473 3.353,8.621 0.520,0.148 10 0.5 sec. 0.149,0.078 2.010,0.215 1.860,0.137 10 Security Indicator Light:

Result
Result Proceed to
Code 2-1 or Code 2-3 A
Code 2-2 B



A

3.READ VALUE USING INTELLIGENT TESTER

B

REGISTRATION AS ANOTHER KEY

3.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Transponder S-code Number of registered sub-keys / min.: 0, max.: 3 Number of registered sub-keys -
Transponder M-code Number of registered master keys / min.: 0, max.: 5 Number of registered master keys -

Result
Result Proceed to
None of the following A
Registered master keys: 5, registered sub-keys: 0 B
Registered master keys: 0, registered sub-keys: 3 C
Registered master keys: 5, registered sub-keys: 3 D



A

4.KEY REGISTRATION

B

KEY REGISTRATION (SUB-KEY)

C

KEY REGISTRATION (MASTER KEY)

D

NOT KEY REGISTRATION

4.KEY REGISTRATION
a.

Refer to the table below to determine if additional keys can be registered.

Number of Keys Registered (Master and Sub) Proceed to
0 New key ID registration (refer to the Service Bulletin)
1 to 7 Additional key ID registration (refer to the Service Bulletin)


b.

Check whether key registration.



OK

END (KEY IS MALFUNCTIONING)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Inspect the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH)
a.

Disconnect the E94 unlock warning switch assembly connector.


b.

Disconnect the E96 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E94-1 - E96-3 (KSW) Always Below 1 Ω
E94-2 - Body ground Always Below 1 Ω
E94-1 - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Inspect the front door courtesy light switch assembly LH (See page Vehicle Interior>LIGHTING (INT)>DOOR COURTESY LIGHT(for Front)>REMOVAL).



OK

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH)
a.

Disconnect the K2 front door courtesy light switch assembly LH connector.


b.

Disconnect the E96 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-1 - E96-7 (CTY) Always Below 1 Ω
K2-1 - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR