Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the combination meter. This circuit provides 2 power source types: one is a constant power source mainly used as a backup power source, and the other is a power source mainly used for signal transmission. The constant power source is mainly used as a backup power source for the meter CPU. However, it is also used for communication. If a voltage of 12 V is not applied to terminal IG+ when the ignition switch isON, indicators will not operate.

WIRING DIAGRAM

U165900E01
1.091,3.708 1.621,3.850 0.531,0.142 10 Battery 2.973,0.85 3.527,1.024 0.554,0.174 10 ECU-B1 3.075,1.765 3.435,1.930 0.360,0.165 10 MET 1.226,1.606 2.215,1.781 0.989,0.174 10 from IG2 Relay 5.146,3.268 5.348,3.415 0.202,0.147 10 E7 5.494,2.592 5.697,2.752 0.202,0.161 10 ET 5.494,1.62 5.764,1.776 0.269,0.156 10 IG+ 5.494,0.691 5.618,0.833 0.123,0.142 10 B 5.244,0.596 5.441,0.752 0.198,0.156 10 17 5.244,1.52 5.441,1.672 0.198,0.151 10 18 5.248,2.508 5.441,2.660 0.193,0.151 10 15 5.146,3.459 6.994,3.620 1.848,0.161 10 Combination Meter Assembly

PROCEDURE

1.INSPECT FUSE (MET, ECU-B1)
a.

Remove the MET and ECU-B1 fuses from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MET fuse Always Below 1 Ω
ECU-B1 fuse




OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
U165929E01
2.375,2.986 2.494,3.151 0.119,0.165 10 B 1.754,2.986 2.016,3.133 0.262,0.147 10 IG+ 2.782,2.986 2.998,3.142 0.216,0.156 10 ET 2.111,2.376 2.426,2.966 false 2.025,2.37 1.894,2.96 false 2.277,2.376 2.885,2.966 false 0.564,2.144 0.767,2.291 0.202,0.147 10 E7 0.309,0.168 2.618,0.504 2.309,0.336 10 Rear view of wire harness connector: (to Combination Meter Assembly)

a.

Disconnect the E7 meter connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-15 (ET) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-17 (B) - Body ground Always 11 to 14 V
E7-18 (IG+) - Body ground Ignition switch ON



Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C


A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C