Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Oil Pressure Gauge Malfunction  


DESCRIPTION

The oil pressure sender detects the oil pressure generated when the engine is started. The combination meter determines that the engine is running when the engine speed is 400 rpm or more, and determines that the engine is cranking when the engine speed is 200 rpm or less. The oil pressure receiver gauge detects and indicates the oil pressure applied to the oil pressure sender.

WIRING DIAGRAM

E158843E03
1.971,1.581 2.315,1.737 0.343,0.156 10 ECM 3.181,1.311 3.815,1.481 0.634,0.170 10 CAN Line 2.141,2.532 2.422,2.674 0.281,0.142 10 D18 2.141,2.711 3.832,3.055 1.691,0.343 10 Oil Pressure Sender Gauge Assembly*1, *2, *4 3.124,2.141 3.225,2.296 0.100,0.156 10 1 2.92,2.233 3.041,2.396 0.121,0.163 10 S 4.347,2.141 4.524,2.296 0.177,0.156 10 11 4.586,2.328 4.707,2.491 0.121,0.163 10 S 2.141,4.906 2.422,5.048 0.281,0.142 10 C33 2.141,5.086 3.492,5.429 1.350,0.343 10 Oil Pressure Sender Gauge Assembly*3 5.401,3.153 5.654,3.302 0.253,0.149 10 OIL 4.579,3.84 4.700,4.003 0.121,0.163 10 S 4.57,4.214 4.823,4.370 0.253,0.156 10 IG+ 4.577,4.607 4.698,4.756 0.121,0.149 10 E 2.631,3.753 3.037,3.902 0.406,0.149 10 VOUT 2.823,4.137 3.041,4.279 0.218,0.142 10 VC 2.721,4.526 3.051,4.668 0.330,0.142 10 GND 3.131,4.429 3.239,4.585 0.107,0.156 10 1 3.131,3.653 3.239,3.809 0.107,0.156 10 2 3.131,4.037 3.239,4.193 0.107,0.156 10 3 4.343,3.653 4.527,3.795 0.184,0.142 10 16 4.343,4.429 4.527,4.571 0.184,0.142 10 24 4.343,4.037 4.527,4.179 0.184,0.142 10 17 4.266,4.906 4.457,5.055 0.191,0.149 10 E8 4.266,5.086 6.117,5.263 1.850,0.177 10 Combination Meter Assembly 0.385,4.432 1.444,4.588 1.059,0.156 10 *1: for 1UR-FE 0.385,4.761 1.416,4.917 1.031,0.156 10 *2: for 1VD-FTV 0.385,5.09 1.333,5.246 0.948,0.156 10 *3: for 1GR-FE 0.385,5.439 1.333,5.595 0.948,0.156 10 *4: for 3UR-FE

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
CAN communication system DTC is not output A
CAN communication system (for LHD) DTC is output B
CAN communication system (for RHD) DTC is output C



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OIL PRESSURE SENSOR)

B

C

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OIL PRESSURE SENSOR)
a.

Operate the intelligent tester according to the display and select Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Oil Pressure Meter Operation Oil pressure receiver gauge LOW, 1/4, 1/2, 3/4 or HIGH Perform the test with the vehicle stopped and engine idling.

OK:

Needle indication is normal.


Result
Result Proceed to
OK A
NG (w/ Multi-information Display) B
NG (w/o Multi-information Display) C



A

3.INSPECT OIL PRESSURE GAUGE ASSEMBLY (OIL PRESSURE SENSOR)

B

C

3.INSPECT OIL PRESSURE GAUGE ASSEMBLY (OIL PRESSURE SENSOR)
a.
E157228

Check that the needle moves in accordance with the engine speed.

OK:

Needle is as shown in illustration when engine is stopped.

Needle moves when engine is running.


Result
Result Proceed to
Oil pressure receiver gauge operates correctly according to engine condition A
Oil pressure receiver gauge does not operate correctly according to engine condition (for 1GR-FE) B
Oil pressure receiver gauge does not operate correctly according to engine condition (for 1UR-FE) C
Oil pressure receiver gauge does not operate correctly according to engine condition (for 3UR-FE) D
Oil pressure receiver gauge does not operate correctly according to engine condition (for 1VD-FTV) E



A

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE SENSOR)

B

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

C

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

D

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

E

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE SENSOR)
E349741E01
0.74,1.865 1.063,2.073 0.323,0.208 4.604,1.833 4.927,2.042 0.323,0.208 1.031,1.385 1.729,1.948 true 5.521,2.01 6.031,2.188 true 1.021,0.323 3.083,0.74 2.063,0.417 10 false Rear view of harness connector: (to Combination Meter Assembly) 0.844,1.208 1.021,1.396 0.177,0.188 10 false S 0.823,1.885 1.115,2.094 0.292,0.208 10 false E8 4.646,1.865 4.979,2.073 0.333,0.208 10 false D18 6.125,2.135 6.375,2.354 0.25,0.219 10 false S 4.625,0.313 6.688,0.729 2.063,0.417 10 false Front view of harness connector: (to Oil Pressure Sensor)

a.

for 1UR-FE, 3UZ-FE, 1VD-FTV:

i.

Disconnect the E8 meter connector.


ii.

Disconnect the D18 gauge connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E8-11 (S) - D18-1 (S) Always Below 1 Ω
E8-11 (S) or D18-1 (S) - Body ground Always 10 kΩ or higher




E349742E01
0.906,1.563 1.229,1.823 0.323,0.26 4.26,1.615 4.583,1.875 0.323,0.26 2.521,2.26 2.125,1.854 true 2.229,1.833 2.75,1.458 true 5.438,1.75 5.958,1.99 true 4.771,2.146 5.063,1.792 true 5.448,2.188 5.24,1.76 true 1.365,2.167 1.688,1.854 true 0.865,0.323 3.125,0.74 2.26,0.417 10 false Rear view of wire harness connector: (to Combination Meter Assembly) 0.979,1.604 1.25,1.833 0.271,0.229 10 false E8 2.885,1.344 3.115,1.583 0.229,0.24 10 false S 2.656,2.229 3.01,2.479 0.354,0.25 10 false IG+ 1.188,2.146 1.427,2.385 0.24,0.24 10 false E 4.229,0.344 6.958,0.76 2.729,0.417 10 false Front view of wire harness connector: (to Oil Pressure Sender Gauge Assembly) 4.313,1.667 4.656,1.896 0.344,0.229 10 false C33 4.458,2.188 4.854,2.427 0.396,0.24 10 false GND 5.333,2.292 5.844,2.51 0.51,0.219 10 false VOUT 6.063,2 6.344,2.24 0.281,0.24 10 false VC

b.

for 1GR-FE:

i.

Disconnect the E8 meter connector.


ii.

Disconnect the C33 gauge connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E8-16 (S) - C33-2 (VOUT) Always Below 1 Ω
E8-17 (IG+) - C33-3 (VC)
E8-24 (E) - C33-1 (GND)
E8-16 (S) or C33-2 (VOUT) - Body ground Always 10 kΩ or higher
E8-17 (IG+) or C33-3 (VC) - Body ground




Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C


A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C