Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Voltage Meter Malfunction  


DESCRIPTION

The voltmeter indicates the voltage applied to the IG+ terminal of the combination meter.

WIRING DIAGRAM

E146354E04
1.076,1.01 2.084,1.175 1.008,0.165 10 from IG2 Relay 3.218,1.186 3.550,1.351 0.332,0.165 10 MET 4.316,2.736 4.509,2.892 0.193,0.156 10 E7 4.174,0.905 4.367,1.089 0.193,0.184 10 18 4.174,1.985 4.367,2.169 0.193,0.184 10 15 4.448,0.926 4.706,1.091 0.258,0.165 10 IG+ 4.448,1.999 4.659,2.155 0.211,0.156 10 ET 5.371,0.767 5.694,0.933 0.323,0.165 10 CPU 5.709,1.729 6.096,1.876 0.387,0.147 10 VOLT 4.316,2.925 6.166,3.099 1.850,0.174 10 Combination Meter Assembly

PROCEDURE

1.INSPECT FUSE (MET)
a.

Remove the MET fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MET fuse Always Below 1 Ω




OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VOLTMETER)

NG

REPLACE FUSE

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VOLTMETER)
a.

Operate the intelligent tester according to the display and select Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Volt meter Operation Voltmeter 0, 3, 6, 9, 12, 15, or 18 Perform the test with the vehicle stopped and engine idling.

OK:

Needle indication is normal.


Result
Result Proceed to
OK A
NG (w/ Multi-information Display) B
NG (w/o Multi-information Display) C



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)

B

C

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)
U165930E01
0.532,2.019 0.743,2.175 0.211,0.156 10 E7 2.065,2.848 2.336,3.004 0.272,0.156 10 IG+ 2.704,2.525 2.916,2.685 0.211,0.161 10 ET 2.042,2.282 2.214,2.838 false 2.289,2.282 2.678,2.574 false 0.318,0.174 2.641,0.524 2.323,0.350 10 Rear view of wire harness connector: (to Combination Meter Assembly)

a.

Disconnect the E7 meter connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-15 (ET) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-18 (IG+) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C