Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is output when the combination meter detects a fuel sender gauge malfunction via the CAN.

DTC Code DTC Detection Condition Trouble Area
B1500 When the combination meter detects a fuel sender gauge malfunction.
·

Harness or connector

·

Combination meter assembly

·

Fuel suction with pump and gauge tube assembly

·

Fuel sender gauge assembly



WIRING DIAGRAM

E197359E03
0.948,1.802 2.844,2.125 1.896,0.323 10 false Fuel Sender Gauge Assembly 1.083,2.542 2.854,3.115 1.771,0.573 10 false Fuel Suction with Pump and Gauge Tube Assembly 5,4.042 6.917,4.5 1.917,0.458 10 false Combination Meter Assembly 4.802,0.594 5.031,0.792 0.229,0.198 10 false 9 4.792,1.125 5.021,1.323 0.229,0.198 10 false 21 4.76,2.781 4.99,2.979 0.229,0.198 10 false 15 2.979,0.719 3.208,0.917 0.229,0.198 10 false 2 2.979,1.229 3.208,1.427 0.229,0.198 10 false 3 2.406,1.24 2.635,1.438 0.229,0.198 10 false 1 1.271,1.25 1.458,1.448 0.188,0.198 10 false 2 2.135,1.281 2.365,1.479 0.229,0.198 10 false FE 1.479,1.271 1.708,1.469 0.229,0.198 10 false FS 2.688,1.26 2.917,1.458 0.229,0.198 10 false FE 2.688,0.74 2.917,0.938 0.229,0.198 10 false FS 5.115,0.781 5.344,0.979 0.229,0.198 10 false L 5.115,1.229 5.344,1.427 0.229,0.198 10 false E 5.135,2.896 5.365,3.094 0.229,0.198 10 false ET 6.208,1.823 6.656,2.021 0.448,0.198 10 false FUEL 4.802,0.865 5.031,1.063 0.229,0.198 10 false E8 4.781,1.385 5.01,1.583 0.229,0.198 10 false E8 4.781,3.042 5.01,3.24 0.229,0.198 10 false E7 1.083,2.323 1.365,2.542 0.281,0.219 10 false N1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE)
a.

Operate the intelligent tester according to the display and select the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5 Fuel sender input value Unit: L

OK:

Fuel value displayed on the intelligent tester is almost the same as needle indication.


Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - PUMP AND GAUGE AND BODY GROUND)

B

C

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - PUMP AND GAUGE AND BODY GROUND)
U165928E02
3.75,1.813 4.01,2.281 false 1.26,1.719 0.875,2.219 false 1.26,1.813 1.646,2.25 false 5.833,1.49 5.354,1.865 false 6.031,1.49 6.292,1.958 false 2.375,1.635 2.573,1.802 0.198,0.167 10 false E7 0.583,1.646 0.781,1.813 0.198,0.167 10 false E8 5.01,1.479 5.208,1.646 0.198,0.167 10 false N1 1.229,0.094 3.583,0.427 2.354,0.333 10 false Rear view of wire harness connector: (to Combination Meter Assembly) 1.719,2.229 1.844,2.385 0.125,0.156 10 false E 0.76,2.219 0.865,2.365 0.104,0.146 10 false L 4.01,2.302 4.219,2.469 0.208,0.167 10 false ET 4.76,0.073 7.115,0.406 2.354,0.333 10 false Front view of wire harness connector: (to Fuel Sender Gauge Assembly) 5.115,1.833 5.344,2.01 0.229,0.177 10 false FS 6.292,1.979 6.49,2.177 0.198,0.198 10 false FE

a.

Disconnect the E7 and E8 combination meter assembly connectors.


b.

Disconnect the N1 fuel suction with pump and gauge tube assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E8-9 (L) - N1-2 (FS) Always Below 1 Ω
E8-21 (E) - N1-3 (FE) Always Below 1 Ω
E7-15 (ET) - Body ground Always Below 1 Ω
E8-9 (L) or N1-2 (FS) - Body ground Always 10 kΩ or higher




OK

3.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
E158805E05
0.217,0.11 0.975,0.294 0.758,0.184 10 *1 2.507,0.549 2.753,0.712 0.246,0.163 10 FS 0.427,1.203 0.673,1.365 0.246,0.163 10 FE 2.916,3.105 3.162,3.268 0.246,0.163 10 FS 2.916,3.839 3.162,4.001 0.246,0.163 10 FE 1.355,1.28 0.745,1.28 false 1.836,1.22 2.425,0.631 false 2.355,3.924 2.865,3.924 false 1.811,3.912 2.876,3.185 false 0.615,0.659 1.411,0.824 0.796,0.165 10 *2 0.615,3.1 1.411,3.265 0.796,0.165 10 *3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 (FS) Always Below 1 Ω
A-3 (FE) - B-1 (FE) Always Below 1 Ω


Text in Illustration
*1 Component without harness connected
(Fuel Suction with Pump and Gauge Tube Assembly)
*2 Connector A
*3 Connector B

Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1UR-FE) C
NG (for 3UR-FE) D
NG (for 1VD-FTV) E



A

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

C

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

D

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

E

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
E154367E02
0.157,0.102 0.502,0.367 0.345,0.265 10 *1 0.945,1.668 1.476,1.960 0.531,0.292 10 FE 1.617,1.668 2.148,1.960 0.531,0.292 10 FS 1.264,1.264 1.089,1.668 false 1.711,1.264 1.711,1.668 false 0.827,4.324 0.974,4.478 0.147,0.154 10 E 0.953,4.401 1.42,4.401 false 0.827,2.105 0.974,2.259 0.147,0.154 10 F 0.953,2.182 1.42,2.182 false


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FS) - 1 (FE) Float level is F (upper) 13.5 to 16.5 Ω
Float level is E (lower) 405.5 to 414.5 Ω


Text in Illustration
*1 Component without harness connected
(Fuel Sender Gauge Assembly)

Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1UR-FE) C
NG (for 3UR-FE) D
NG (for 1VD-FTV) E



A

5.CHECK COMBINATION METER TYPE

B

C

D

E

5.CHECK COMBINATION METER TYPE
a.

Check the combination meter type

Result
Result Proceed to
w/ Multi-information Display A
w/o Multi-information Display B



A

B