Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825/56  Short in Side Squib LH Circuit  B1826/56  Open in Side Squib LH Circuit  B1827/56  Short to GND in Side Squib LH Circuit  B1828/56  Short to B+ in Side Squib LH Circuit  


DESCRIPTION

The side squib LH circuit consists of the center airbag sensor and the front seat airbag LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1825/56 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the side squib LH circuit during the primary check.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1826/56 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the side squib LH circuit for 2 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1827/56 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the side squib LH circuit for 0.5 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1828/56 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the side squib LH circuit for 0.5 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C178002E14
1.928,1.577 2.312,1.744 0.385,0.167 10 SFL+ 2.427,1.577 2.567,1.744 0.140,0.167 10 1 4.486,1.577 4.626,1.744 0.140,0.167 10 1 2.427,2.417 2.567,2.585 0.140,0.167 10 2 4.486,2.417 4.626,2.585 0.140,0.167 10 2 4.728,1.577 5.113,1.744 0.385,0.167 10 SFL+ 1.928,2.42 2.312,2.587 0.385,0.167 10 SFL- 4.743,2.42 5.128,2.587 0.385,0.167 10 SFL- 0.701,3.101 1.112,3.269 0.411,0.167 10 Kz4 0.701,3.298 1.728,3.465 1.026,0.167 10 Side Squib LH 4.826,4.229 5.101,4.396 0.275,0.167 10 K27 4.826,4.426 6.227,4.593 1.400,0.167 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT AIRBAG LH (SIDE SQUIB LH)
a.
U164493E02
1.042,0.417 0.885,1 false 2.344,3.698 2.865,3.698 false 2,3.844 2.188,4.188 2.188,4.188 2.354,4.188 false 0.365,1.958 2.771,2.292 2.406,0.333 10 false Front view of wire harness connector: (to Side Squib LH) 1.719,1.156 3.177,1.375 1.458,0.219 10 false Center Airbag Sensor 0.271,1.042 1.24,1.198 0.969,0.156 10 false Side Squib LH 1.156,0.49 1.313,0.677 0.156,0.188 10 false D 1.375,0.479 1.552,0.667 0.177,0.188 10 false C 2.885,3.604 3.26,3.802 0.375,0.198 10 false SST 2.406,4.115 3.125,4.313 0.719,0.198 10 false Color: Red 2.354,2.865 3.208,3.073 0.854,0.208 10 false Connector C 0.51,3.438 0.802,3.625 0.292,0.188 10 false Kz4

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat airbag LH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827 or B1828 is not output.


HINT:

Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.


Result
Result Proceed to
OK (for Manual Seat) A
OK (for Power Seat) B
NG C



A

B

C

2.CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)
2.CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)
a.
U164495E02
1.823,0.094 1.74,0.094 1.74,0.094 1.667,0.479 false 1.052,0.615 0.823,0.99 false 0.635,4.135 1.094,3.823 false 1.365,3.781 1.875,4.083 false 1.802,0.438 1.854,0.396 false 1.802,0.51 1.906,0.396 false 1.802,0.573 1.906,0.469 false 1.802,0.635 1.906,0.531 false 1.854,0.646 1.906,0.594 false 0.167,2.375 2.563,2.75 2.396,0.375 10 false Front view of wire harness connector: (to Side Squib LH) 1.646,1.354 3.042,1.573 1.396,0.219 10 false Center Airbag Sensor 1.885,0.052 2.688,0.271 0.802,0.219 10 false Floor Wire 0.146,1 1.292,1.365 1.146,0.365 10 false Side Squib LH 1.188,0.688 1.354,0.875 0.167,0.188 10 false D 1.396,0.688 1.542,0.885 0.146,0.198 10 false C 1.781,0.688 1.927,0.865 0.146,0.177 10 false B 2.156,0.448 2.302,0.635 0.146,0.188 10 false A 1.99,3.333 2.833,3.5 0.844,0.167 10 false Connector C 1.948,4.021 2.302,4.177 0.354,0.156 10 false SFL- 0.24,4.073 0.615,4.229 0.375,0.156 10 false SFL+ 0.177,3.333 0.438,3.479 0.26,0.146 10 false Kz4

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Kz4-1 (SFL+) - Body ground Ignition switch ON Below 1 V
Kz4-2 (SFL-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Kz4-1 (SFL+) - Kz4-2 (SFL-) Always Below 1 Ω



j.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Kz4-1 (SFL+) - Kz4-2 (SFL-) Always 1 MΩ or higher
Kz4-1 (SFL+) - Body ground Always 1 MΩ or higher
Kz4-2 (SFL-) - Body ground Always 1 MΩ or higher




OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
a.
C146259E42
0.865,0.573 0.792,1.083 false 0.156,1.115 1.25,1.469 1.094,0.354 10 false Side Squib LH 1.594,1.333 2.99,1.552 1.396,0.219 10 false Center Airbag Sensor 1.021,0.646 1.146,0.813 0.125,0.167 10 false D 1.146,0.646 1.281,0.813 0.135,0.167 10 false C

Connect the connectors to the front seat airbag LH and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827 or B1828 is not output.


HINT:

Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.




OK

NG